1993 Land Rover Defender

Front Outer Seat belt webbing slightly damaged or frayed both sides (7.1.2 (b) (ii))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Front Shock absorbers has a slightly worn bush lower bush (5.3.2 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear bump stops missing

Nearside Front Suspension component ball joint has slight play (5.3.4 (a) (i))

rear chassis corroded

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Fuel cap/sealing device ineffective (6.1.3 (b) (i))

Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

front trailing arms slightly corroded

Nearside Rear Suspension component mounting prescribed area is excessively corroded x2 (2.4.A.3)

Nearside Track rod end excessively corroded and unserviceable nut (2.2.C.1d)

front trailing arms slightly corroded

Offside front hub weeping oil

Power steering component(s) has slight seepage from a component Steering box (2.3.3b)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside front hub weeping oil

Power steering component(s) has slight seepage from a component Steering box (2.3.3b)

Corrosion to offside shock mounting tower.

Brake pipe excessively corroded Front to rear (3.6.B.2c)

Centre Rear Torque/reaction arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Front registration plate character(s) likely to be misread (6.3.4b)

Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting chassis (6.6.6)

Nearside Windscreen wiper not operating over a large enough area to give an adequate view (8.2.1c)

Offside Front Steering component mounting prescribed area is excessively corroded outer top cross member (2.2.C.1h)

Offside Front Suspension component mounting prescribed area is excessively corroded outrigger (2.4.A.3)

Offside Rear Brake pipe inadequately clipped (3.6.B.1)

Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting chassis (6.6.6)

Nearside Drag link end ball joint has excessive play (2.2.B.1f) DANGEROUS

Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded bulk head (3.6.C.3) DANGEROUS

Offside Front Outer Steering component mounting prescribed area is excessively corroded chassis (2.2.C.1h) DANGEROUS

Offside Front Steering component mounting prescribed area is excessively corroded bulk head (2.2.C.1h) DANGEROUS

Steering retaining device insecure Steering shaft to steering box coupling (2.2.C.1g) DANGEROUS

Oil leaks from oil pressure switch and gearbox

corrosion to offside shock mounting tower

Front Brake pipe slightly corroded (3.6.B.2c)

advise oil pressure switch leaking

advise rear crossmember covered unable to inspect fully

Front Brake pipe slightly corroded (3.6.B.2c)

Nearside Side repeater not working (1.4.A.2c)

advise oil pressure switch leaking

advise rear crossmember covered unable to inspect fully

Brake pipe slightly corroded (3.6.B.2c)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.6.6)

Offside Rear position lamp(s) not working (1.1.A.3b)

Registration plate lamp not working (1.1.C.1d)

Windscreen washer provides insufficient washer liquid (8.2.3)

Rear Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

adv alternator belt loose

unable to carry out full inspection of rear cross member due to aluminum covering

Centre Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.6.6)

Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.6.6)

Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)

Offside Front Steering component mounting prescribed area is excessively corroded (2.2.C.1h)

Offside Rear Direction indicators not working (1.4.A.2c)

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

adv alternator belt loose

unable to carry out full inspection of rear cross member due to aluminum covering

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Front Front position lamp(s) not working (1.1.A.3b)

Offside Headlamp not in good working order (not working) (1.2.4a)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Front Brake pipe slightly corroded (3.6.B.2c)

Front coil spring corroded (2.4.C.1b)

Rear coil spring worn (2.4.C.1b)

both steering swivel slightly leaking on front axels

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Front Brake pipe excessively corroded (3.6.B.2c)

Offside Front brake disc excessively pitted (3.5.1h)

Stop lamp not working (1.2.1b)

corrosion rear crossmember

front pads low

rear axle corroded

rear wiper split

Headlamp not working on main beam (1.7.5a)

Nearside Rear Upper Coil spring not correctly located (2.4.C.2)

Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Tyre tread depth below requirements of 1.6mm (4.1.E.1)