1994 Toyota Land Cruiser

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Brake performance unable to be tested (1.2.1 (g))

Nearside Front Body panel corroded and likely to cause injury door (6.2.1 (a) (i))

Offside Front Body panel corroded and likely to cause injury wing (6.2.1 (a) (i))

Offside Front Lower Coil spring mounting corroded and seriously weakened (5.3.1 (b) (i))

Offside Position lamp showing white light to the rear (4.2.3 (a) (ii))

Rear Brake disc significantly and obviously worn (1.1.14 (a) (i))

Rear Bumper insecure (6.1.4 (a) (i))

Rear Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Rear Tyre obviously under inflated (5.2.3 (l))

Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))

Nearside Rear Upper Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Front Lower Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))

Offside Rear Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Rear Brake pad(s) wearing thin Both (1.1.13 (a) (ii))

Rear Prop shaft joint worn, but not excessively (6.1.7 (c) (i))

Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i))

Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Axle (5.3.6 (a) (i))

Nearside Rear Lower Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened Axle (5.3.3 (b) (i))

Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))

Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Axle (5.3.6 (a) (i))

Offside Rear Lower Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Rear Prop shaft joint worn, but not excessively (6.1.7 (c) (i))

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))

Nearside Rear Upper Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Front Lower Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))

Offside Rear Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Rear Brake pad(s) wearing thin Both (1.1.13 (a) (ii))

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Offside Front Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Power steering pump has slight seepage (2.1.5 (a))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Offside Front Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Power steering pump has slight seepage (2.1.5 (a))

Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Horn not working (7.7 (a))

Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))

Offside Rear Bumper insecure (6.1.4 (a) (i))

Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Nearside Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Power steering pump has slight seepage (2.1.5 (a))

Integral body structure is corroded but structural rigidity is not significantly reduced various places (6.1.1 (c) (i))

Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security various mounts but not considered to affect body security (6.2.2 (d) (i))

Nearside Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Oil leak, but not excessive hub seal (8.4.1 (a) (i))

Nearside Rear Lower Suspension arm pin or bush worn but not resulting in excessive movement front trailing arm bush (5.3.4 (a) (i))

Offside Front Lower Coil spring mounting corroded but not seriously weakened mounting cup (5.3.1 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Power steering pump has slight seepage (2.1.5 (a))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Rear Exhaust mounting defective mounting rubber broken (6.1.2 (a))

Rear Suspension arm corroded but not seriously weakened both sides (5.3.3 (b) (i))

Trailer electrical socket insecure (4.10 (a) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced various places - some areas close to fail criteria (6.1.1 (c) (i))

Nearside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Nearside Front Brake disc contaminated (1.1.14 (b))

Nearside Front Fluid leak harmful to the environment or a risk to other road users swivel (8.4.1 (a) (i))

Offside Rear Parking brake inoperative on one side (1.4.1 (a))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Nearside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Front Registration plate does not conform to the specified requirements (0.1 (d))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear Parking brake inoperative on one side (1.4.1 (a))

Offside Stop lamp(s) emits other than a steady red light (4.3.3 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Registration plate does not conform to the specified requirements (0.1 (d))

Windscreen washer not working (3.5 (a))

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Fluid leak, but not excessive swivels (8.4.1 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Front Wiper motor works on slow speed only.

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

Rear corrosion around rear body mount o/s above rear axle and n/s rear mount

Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Boot lid cannot be secured in the closed position (6.2.1 (e))

Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i))

Offside Front Coil spring fractured or broken (5.3.1 (b) (i))

Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Front Wiper motor works on slow speed only.

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

Rear corrosion around rear body mount o/s above rear axle and n/s rear mount

Nearside Front Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Oil leak, but not excessive (8.4.1 (a) (i))

Offside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Front Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Oil leak, but not excessive (8.4.1 (a) (i))

Offside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Brackets on rear axle corroded

Offside and nearside inner sills corroded

Offside and nearside rear chassis corroded

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill (5.2.6)

Offside Rear Rear position lamp(s) incorrect colour (1.1.A.3e)

Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill (5.2.6)

Rear Stop lamp not working offside and nearside (1.2.1b)

Brackets on rear axle corroded

Offside and nearside inner sills corroded

Offside and nearside rear chassis corroded

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

both front hub assembly's have light misting of oil

offside and nearside inner sills corroded

rear axle corroded

rear suspension arms corrodd

Nearside Front Anti-roll bar linkage fractured (2.4.G.1)

Offside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Stop lamp emits other than a steady red light (1.2.1e)

Rear Registration plate lamp insecure (1.1.C.1c)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

both front hub assembly's have light misting of oil

offside and nearside inner sills corroded

rear axle corroded

rear suspension arms corrodd

Offside Rear Shock absorber has a light misting of oil (2.7.3)

Rear Shock absorber has slight corrosion to the casing (2.7.2a)

n/s side step inscure

o/s and n/s front swivls leaking oil slightly

rear axel slightly corroded

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Brakes imbalanced across an axle (3.7.B.5b)

Front front brake application uneven (3.7.B.2)

Nearside Front Brake hose stretched (found during steering lock to lock check) (2.2.D.2b)

Offside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Rear position lamp(s) incorrect colour (1.1.A.3e)

Offside rear brake binding (3.7.B.1)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Rear Brake valve corroded and excessively weakened (3.6.A.2b)

rear brake application uneven (3.7.B.2)

Offside Front Brake hose bulging under pressure (3.6.B.3) DANGEROUS

Offside Front Brake hose leaking (3.6.A.1) DANGEROUS

Offside Rear Shock absorber has a light misting of oil (2.7.3)

n/s side step inscure

o/s and n/s front swivls slightly leaking oil

rear axel slightly corroded

Offside rear parking brake recording little or no effort (3.7.B.6a)

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Offside Rear position lamp(s) incorrect colour (1.1.A.3e)

Parking brake: efficiency below requirements (3.7.B.7)

Rear Tyre(s) incorrect because tyres with different aspect ratios are fitted on the same axle. (4.1.A.1a)

Prop-shaft flange bolt(s) loose/missing

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

front dif lock missing

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Brake pedal feels spongy with the vacuum fully depleted (3.3.C.2)

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Front Anti-lock braking system component excessively damaged (3.4.2)

Nearside Rear Brake load sensing valve linkage seized (3.6.E.3)

Nearside Rear Brake valve insecurely mounted (3.6.A.2a)

Offside Front Steering locking device missing (2.2.C.1g)

Rear Rear fog lamp not working (1.3.2b)

Service brake: efficiency below requirements (3.7.B.7)

Prop-shaft flange bolt(s) loose/missing

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

front dif lock missing

Nearside Front wheel bearing has slight play (2.5.A.3c)

Nearside Front Brake hose bulging under pressure (3.6.B.3)

Nearside Front wheel bearing has slight play (2.5.A.3c)

Front Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Drag link end ball joint has excessive play (2.2.B.1f)

Nearside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Centre Rear Brake pipe slightly corroded (3.6.B.2c)