1994 Honda C90

Brake locking device missing rear torque arm (3.2.A1e)

Front Brake lever has inadequate reserve travel (3.1.3b)

Leg shield insecure and likely to impede the steering (2.1.2e)

Rear Brake reaction bracket securing bolt(s) loose (3.2.A1j)

Rear Drive chain excessively loose (6.2.1d)

Rear wheel spindle securing nut locking device missing (2.4.A.2b)

Steering headbearing has excessive free play (2.2.2)

Front Wheel corroded significantly reducing the original strength (4.2.1a) DANGEROUS

Rear Tyre fouling another component (4.1.4) DANGEROUS

Rear Brake pedal pivots slightly worn (3.1.3a)

slight wear or free play in a front suspension component

Upper Steering headbearing has slight free play (2.2.2)

Plate brake test The less effective brake control does not achieve an efficiency of 25%. (3.3.B2b)

Upper Steering headbearing has slight free play (2.2.2)

Brake pedal pivots slightly worn (3.1.3a)

Rear Drive chain sprocket slightly worn (6.2.1e)

Rear Wheel spoke slightly loose. (4.2.1b)

Rear Wheel spoke cracked. brocken (4.2.1b)

Rear position lamp does not illuminate immediately when it is switched on (1.1.3a)

Rear suspension bush has excessive free play swing arm (2.4.A2a(i))

Rear wheel spindle securing nut locking device missing (2.4.A.2b)

Stop lamp does not illuminate immediately a brake applies (1.3.1a)

Brake pedal pivots slightly worn (3.1.3a)

Rear Drive chain sprocket slightly worn (6.2.1e)

Rear Wheel spoke slightly loose. (4.2.1b)

Headlamp at least one does not illuminate on main beam (1.2.2a(ii))

Headlamp dipped beam affected by the operation of another lamp (1.2.2c)

Rear Brake reaction bracket insecure (3.2.A1j)

Stop lamp affected by the operation of another lamp (1.3.2)

Brake pedal has inadequate reserve travel (3.1.3b)

Locking device(s) not correctly fitted which may make the motor bicycle dangerous to ride (6.2.1h)

Rear Wheel alignment incorrect which adversely affects the handling (2.5.1)

Brake pedal has inadequate reserve travel (3.1.3b)

Direction indicator flashing less than 60 times a minute (1.5.1c)

Floor brake test No brake control achieves an efficiency of 30%. (3.3.C1a)

Front Brake lever cannot be released smoothly (3.1.3d)

Front Brake lever has inadequate reserve travel (3.1.3b)

Front Stop lamp does not illuminate immediately a brake applies (1.3.1a)

Rear Brake lining(s) less than 1.5 mm thick (3.2.A1f(i))

Rear Rear shock absorber has inadequate damping effect. (2.4.A.3b)

Rear Tyre has a tear caused by separation or partial failure of its structure (4.1.2a(ii))

Rear wheel spindle securing nut locking device missing (2.4.A.2b)

Front Brake lining(s) close to minimum limit (3.2.A1f(i))

Rear Brake lining(s) close to minimum limit (3.2.A1f(i))

Drive chain excessively tight (6.2.1d)

Front Brake lining(s) close to minimum limit (3.2.A1f(i))

Rear Brake lining(s) close to minimum limit (3.2.A1f(i))

Rear Wheel alignment incorrect which adversely affects the handling (2.5.1)

Rear position lamp does not illuminate immediately when it is switched on (1.1.3a)

Rear Brake lining(s) close to minimum limit (3.2.A1f(i))

Rear Wheel alignment incorrect which adversely affects the handling (2.5.1)

Front suspension assembly component excessively bent (2.3.1)

Rear Brake lining(s) less than 1.5 mm thick (3.2.A1f(i))

Front Roller brake test indicates a slightly grabbing brake (3.3.A1b)

Front Roller brake test indicates slight fluctuation of brake effort (3.3.A1d)

Front Wheel has a slightly eccentric bead rim. (4.2.2)

Rear Wheel has a slightly eccentric bead rim. (4.2.2)

Front Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))

Rear Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))

Rear Drive chain slightly loose (6.2.1d)