2010 Kia Proceed

Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear disc backplates missing both sides had brake ok

towbar removed n/s has sharp edge

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear disc backplates missing both sides had brake ok

towbar removed n/s has sharp edge

Nearside Rear Suspension component pin or bush slightly worn Trailing arm (5.3.4 (a) (i))

Offside Rear Suspension component pin or bush slightly worn Trailing arm (5.3.4 (a) (i))

Rear Sub-frame corroded but not seriously weakened And attached components (5.3.3 (b) (i))

Offside Parking brake inoperative on one side (1.4.1 (a))

Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Service brake excessively fluctuating (1.2.1 (e))

Service brake efficiency below requirements (1.2.2 (a) (i))

Nearside Rear Suspension component pin or bush slightly worn Trailing arm (5.3.4 (a) (i))

Offside Rear Suspension component pin or bush slightly worn Trailing arm (5.3.4 (a) (i))

Rear Sub-frame corroded but not seriously weakened And attached components (5.3.3 (b) (i))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement Trailing arm (5.3.4 (a) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement Trailing arm (5.3.4 (a) (i))

Service brake requirements only just met. It would appear that the braking system requires adjustment or repair Parking brake (1.2.1 (c))

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Front Sub-frame is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear Sub-frame is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

fuel tank corroded

nearside front and offside front inner cv boots leaking grease

Offside Front Tyre worn close to legal limit/worn on edge Inner edge (5.2.3 (e))

Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i))

Nearside Front Brakes imbalanced across an axle (1.2.1 (b) (i))

Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i))

Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Front Tyre worn close to legal limit/worn on edge Inner edge (5.2.3 (e))

Tyre worn close to legal limit/worn on edge all worn on inner edge (5.2.3 (e))

Nearside Front Headlamp not working on dipped beam (1.7.5a)

Nearside Rear Stop lamp not working (1.2.1b)

Nearside front brake excessively fluctuating (3.7.B.3)

Offside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Offside front brake excessively fluctuating (3.7.B.3)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

no rear seatbelts or stalks inspected due to dog cage being installed

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Headlamp not working on dipped beam (1.7.5a)

Nearside Registration plate lamp not working (1.1.C.1d)

Nearside Side repeater incorrect colour (1.4.A.2f)

Nearside Stop lamp not working (1.2.1b)

Offside Registration plate lamp not working (1.1.C.1d)

Offside Side repeater incorrect colour (1.4.A.2f)

no rear seatbelts or stalks inspected due to dog cage being installed

could not inspect rear seatbelt stalks due to dog cage being securley installed obstructing inspection