2004 Mercedes-benz C

Exhaust mounting defective (6.1.2 (a))

Front odd head light lenses

Nearside Rear Brake hose slightly deteriorated (1.1.12 (b) (ii))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Brake hose slightly deteriorated (1.1.12 (b) (ii))

Rear Brake pipe corroded, covered in grease or other material both rear over fuel tank (1.1.11 (c))

Rear Exhaust mounting defective (6.1.2 (a))

under tray fitted not allowing full inspection

Nearside Front Headlamp aim so that beam "kick up" is not visible on the screen (4.1.2 (a))

Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt front (5.3.4 (b) (ii))

Nearside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Rear Brake pipe excessively corroded (1.1.11 (c))

Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Rear Brake pipe excessively corroded (1.1.11 (c))

Nearside Front Inner Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Front odd head light lenses

Nearside Rear Brake hose slightly deteriorated (1.1.12 (b) (ii))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Brake hose slightly deteriorated (1.1.12 (b) (ii))

Rear Exhaust mounting defective (6.1.2 (a))

under tray fitted not allowing full inspection

Nearside Front Coil spring fractured or broken (5.3.1 (b) (i))

Nearside Front Lower Suspension arm ball joint excessively worn rearward (5.3.4 (a) (i))

Nearside Front Lower Suspension arm pin or bush excessively worn inner rearward (5.3.4 (a) (i))

Offside Front Lower Suspension arm pin or bush excessively worn inner rearward (5.3.4 (a) (i))

Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Indicator switch faulty (4.4.2 (a) (i))

Nearside Windscreen wiper blade defective (3.4 (b) (i))

Offside Rear Brake pipe corroded, covered in grease or other material to hose (1.1.11 (c))

Rear Anti-roll bar pin or bush worn but not resulting in excessive movement both "D" bushes (5.3.4 (a) (i))

Rear Brake hose slightly damaged both (1.1.12 (b) (i))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

odd headlamp lenses fitted

undertrays fitted unable to fully test underside

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front coil spring broken (2.4.C.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Offside Track rod end ball joint has excessive play (2.2.B.1f)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Track rod end ball joint has slight play (2.2.B.1f)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Oil leak

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)