2003 Toyota Prius

Front Headlamp has a product on the lens but not seriously reducing light output both sides (4.1.4 (b))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Front Headlamp has a product on the lens but not seriously reducing light output both sides (4.1.4 (b))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Rear Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Front Tyre tread pattern not visible over the whole tread area when minimum depth required is 1.0mm both (5.2.3 (e)) DANGEROUS

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Direction indicator slightly discoloured both side (4.4.3 (a))

Nearside Front Direction indicator slightly discoloured (4.4.3 (a))

Nearside Rear Inner Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Rear Fuel Pipe/s corroded ()

Rear Lower Vehicle structure is corroded but structural rigidity is not significantly reduced both side sill (6.1.1 (c) (i))

Wheel alignment recommended.

Nearside Front Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Rear Parking brake lever has little reserve travel (3.1.6b)

Rear Exhaust has a major leak of exhaust gases exhaust bracket broken (7.1.2)

Nearside Front Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Rear Parking brake lever has little reserve travel (3.1.6b)

Nearside Front Outer Tyre worn close to the legal limit (4.1.E.1)

Parking brake lever has little reserve travel (3.1.6b)

Offside Rear bumper area damaged

Rear Brake pad(s) wearing thin 70% (3.5.1g)

Rear Parking brake lever has little reserve travel (3.1.6b)

Brakes imbalanced across an axle (3.7.B.5b)

Offside Rear rear brake binding (3.7.B.1)

Front Brake pad(s) wearing thin (3.5.1g)

front discs corroded

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Front All position lamps not working (1.1.A.3b)

Nearside Registration plate lamp not working (1.1.C.1d)

Nearside Stop lamp not working (1.2.1b)

Offside Headlamp not working on dipped beam (1.7.5a)

front number plate cracked

front number plate cracked

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)