2002 Mercedes-benz Ml

Nearside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Brake disc worn, pitted or scored, but not seriously weakened BOTH (1.1.14 (a) (ii))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Exhaust emissions exceed manufacturer's specified limit (8.2.2.2 (a))

Nearside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii))

Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened BOTH (1.1.14 (a) (ii))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Oil leak ()

Rear Brake pad(s) wearing thin Both Rear Pads Low (3.5.1g)

Nearside Front Inner Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

engine cover

oil leak

under tray fitted

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Brake pipe excessively corroded front to rear (3.6.B.2c)

Offside Front Steering rack gaiter split (2.2.D.2d)

Nearside Front Inner Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

engine cover

oil leak

under tray fitted

Offside Front Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Rear Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Anti-roll bar linkage missing (2.4.G.1)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Headlamp not working on main beam (1.7.5a)

Offside Front Suspension arm has slight play in a ball joint (2.4.G.2)

Rear Registration plate lamp not working (1.1.C.1d)

Offside Front Suspension arm has slight play in a ball joint (2.4.G.2)

Child seat fitted not allowing full inspection of adult belt

Engine covers fitted obscuring some components in the engine bay

Oil leak

Under-trays fitted obscuring some underside components

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Stop lamp not working (1.2.1b)

Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Registration plate lamp not working (1.1.C.1d)

Centre Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Nearside Lower Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Offside Upper Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Centre Upper Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Child seat fitted not allowing full inspection of adult belt

Nearside Lower Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Centre Upper Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Child seat fitted not allowing full inspection of adult belt

Nearside Lower Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Offside Headlamp not working on main beam (1.7.5a)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)