1994 Suzuki Cappuccino

Sub-frame corroded but not seriously weakened front and surface (5.3.3 (b) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Rear Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Offside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened inner faces (1.1.14 (a) (ii))

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. 28% across axle (1.2.1 (b) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill (6.1.1 (c) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to floor (6.1.1 (c) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Fuel Pipe/s corroded ()

Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill inner , seat mounting area (6.1.B.2)

Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill inner (6.1.B.2)

Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill outer next to previous repair (6.1.B.2)

Parking brake lever has little reserve travel (3.1.6b)

Nearside Front engine mounting bracket insecure and likely to fail (6.1.D.1b)

Nearside Rear Rear wheel bearing rough when rotated (2.6.1)

Offside Front engine mounting bracket insecure and likely to fail (6.1.D.1b)

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions hydrocarbon content after 2nd fast idle excessive (7.3.D.3)

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Nearside Inner Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Outer Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Outer Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)