2002 BMW M3

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Direction indicator not working (4.4.1 (a) (ii))

Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))

Front Brake pipe corroded, covered in grease or other material both (1.1.11 (c))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

fuel cap seal perished

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Front Windscreen washer not working (3.5 (a))

Horn not working (7.7 (a) (ii))

Front Brake pipe corroded, covered in grease or other material both (1.1.11 (c))

Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

fuel cap seal perished

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

both front to rear steel brake pipes heavily greased

fuel cap seal cracked

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b))

Horn not working (7.7 (a) (ii))

Rear Exhaust has a major leak of exhaust gases (6.1.2 (a))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

both front to rear steel brake pipes heavily greased

fuel cap seal cracked

Nearside Rear Direction indicator slightly discoloured (4.4.3 (a))

Nearside Rear Tyre worn close to legal limit/worn on edge on inner edge (5.2.3 (e))

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Direction indicator slightly discoloured (4.4.3 (a))

Offside Rear Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Rear Tyre worn close to legal limit/worn on edge on inner edge (5.2.3 (e))

Headlamp levelling device inoperative (1.7.2)

Brake pipe excessively corroded both front to rear (3.6.B.2c)

Headlamp aim too low both (1.8)

Headlamp cleaning device inoperative (1.7.2)

Headlamp levelling device inoperative (1.7.2)

Nearside Rear coil spring broken (2.4.C.1a)

Offside Obligatory mirror missing (8.1.1)

Offside Rear coil spring broken (2.4.C.1a)

Offside rear brake binding (3.7.B.1)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

offside rear outer cv boot deteriorated

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Inner Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Inner Rear Brake pad(s) wearing thin (3.5.1g)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

airbag light on

brake noise offside rear (handbrake shoes?)

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Rear coil spring incomplete (2.4.C.1a)

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Rear Direction indicator slightly discoloured (1.4.A.2f)

center to rear exhaust mouting rusted

Brake pipe slightly corroded (3.6.B.2c)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)