2004 Fiat Panda

Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear Outer Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Emissions not tested due to exhaust blow center to rear joint (8.2.1.2 (d))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Rear Brakes imbalanced across an axle (1.2.1 (b) (i))

Offside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

Nearside Rear Body Sill slightly corroded

Nearside Windscreen wiper blade defective (3.4 (b) (i))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Front Upper Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Position lamp slightly affected by the operation of another lamp (4.2.3 (c))

Offside Rear Tyre worn close to legal limit/worn on edge REPLACE SOON (5.2.3 (e))

Temporary fuel cap fitted

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Parking brake inoperative on one side (1.4.1 (a))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Front Upper Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Position lamp slightly affected by the operation of another lamp (4.2.3 (c))

Offside Rear Tyre worn close to legal limit/worn on edge REPLACE SOON (5.2.3 (e))

Temporary fuel cap fitted

Temporary fuel cap fitted

Nearside Stop lamp(s) not working (4.3.1 (a) (ii))

Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i))

Offside Front Upper Macpherson strut mounting corroded and seriously weakened (5.3.3 (b) (i))

Offside Track rod end ball joint has excessive play (2.1.3 (b) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Temporary fuel cap fitted

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Temporary fuel cap fitted

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Temporary fuel cap fitted

Offside Front Position lamp not working (4.2.1 (a))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

Offside Windscreen wiper blade defective (3.4 (b) (i))

Nearside Front Macpherson strut has slight movement in the upper support bearing assembly (2.5.B.1b)

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Nearside Front Macpherson strut has slight movement in the upper support bearing assembly (2.5.B.1b)

Parking brake: efficiency below requirements (3.7.B.7)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

both front tyres worn out on inside edges

Nail in offside rear tyre

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Front Exhaust has part of the system slightly deteriorated (7.1.1a)

Nearside Front Shock absorber has a light misting of oil (2.7.3)

Oil leak

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Front Exhaust has part of the system slightly deteriorated (7.1.1a)

Nearside Front Shock absorber has a light misting of oil (2.7.3)

Oil leak

Front Exhaust has part of the system slightly deteriorated (7.1.1a)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Rear Exhaust has part of the system slightly deteriorated (7.1.1a)

front discs pitted

Nearside Front Shock absorber has a serious fluid leak (2.7.3)

Nearside Headlamp aim too high (1.8)

Front Exhaust has part of the system slightly deteriorated (7.1.1a)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Rear Exhaust has part of the system slightly deteriorated (7.1.1a)

front discs pitted

Nearside Front Shock absorber has a light misting of oil (2.7.3)

Offside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Offside Front Shock absorber has a light misting of oil (2.7.3)

Offside Front Shock absorber has a slightly reduced damping effect (2.7.5)

Nearside Front Headlamp not working on dipped beam (1.7.5a)