2008 Ford Ka

Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor (6.2.2 (d) (i))

Nearside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor (6.2.2 (d) (i))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer Sill (6.2.2 (d) (i))

Offside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Rear Brake pipe excessively corroded (1.1.11 (c))

Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer & Inner Sill (6.2.2 (d) (i))

Offside Rear Position lamp not working (4.2.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))

around fuel cap corroded

Coil spring fractured or broken (5.3.1 (b) (i))

Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i))

Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Nearside Front Brake disc in such a condition that it is seriously weakened (1.1.14 (a) (ii)) DANGEROUS

Offside Front Brake disc in such a condition that it is seriously weakened (1.1.14 (a) (ii)) DANGEROUS

Offside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))

around fuel cap corroded

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Seat belt anchorage prescribed area is corroded but not considered excessive outer sill (7.1.1 (a) (i))

Offside Rear Seat belt anchorage prescribed area is corroded but not considered excessive sill (7.1.1 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Tyre worn close to the legal limit 3-4mm and wearing on edges slightly, sized 165 60 14 (4.1.E.1)

Rear Inner Subframe mounting prescribed area is corroded but not considered excessive both sill areas (2.4.A.3)

Exhaust system not adequately supported back box (7.1.1)

Registration plate lamp not working both (1.1.C.1d)

Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Inner Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Inner Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Rear Sub-frame rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Slight cracking to OSR tyre

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)