2004 Jaguar XK8

Auxiliary belt cracking

Nearside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Nearside Front Upper Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Front Upper Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Vehicle covered in underseal underneath

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

some rust in n/s front floor

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Front Tyre(s) of different sizes are fitted on the same axle. (5.2.3 (b))

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Lower Suspension component ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Front Inner Tyre worn close to legal limit/worn on edge edge (5.2.3 (e))

slight oil leak reardiff

light corrosion to floor

Exhaust system not adequately supported (7.1.1)

light corrosion to floor

Nearside Front Body has slight corrosion floor pan (6.1.B.2)

engine and under trays fitted

Offside Rear Lower Suspension arm has excessive play in a pin/bush where hub meets arm (2.4.G.2)

Nearside Front Body has slight corrosion floor pan (6.1.B.2)

engine and under trays fitted

n/s/f floor rusted through

o/s/f floor corroding

Offside Front Tyre tread depth below requirements of 1.6mm on inside (4.1.E.1)

Tyre tread depth below requirements of 1.6mm both rear (4.1.E.1)

n/s/f floor rusted through

o/s/f floor corroding

Nearside Side repeater insecure (1.4.A.2b)

Nearside Stop lamp not working (1.2.1b)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

both front tyres just legal on inner edge

Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

both front tyres just legal on inner edge

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Front Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Offside Rear wheel bearing has slight play (2.6.2)

Suspension joint nearside lower dust cover split/missing

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1) DANGEROUS

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1) DANGEROUS