2005 Mercedes-benz Vito

Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outrigger corroded (6.2.2 (d) (i))

Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outrigger corroded (6.2.2 (d) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Nearside Front Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Service brake binding but not excessively (1.2.1 (f))

Offside Rear Service brake binding but not excessively (1.2.1 (f))

Vehicle structure is corroded but structural rigidity is not significantly reduced general corrosion underneath (6.1.1 (c) (i))

Brake disc worn, pitted or scored, but not seriously weakened All four brake discs pitted (1.1.14 (a) (ii))

Both head lights blurred.

Nearside Rear Brake pipe covered in paint preventing complete examination.

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Brake pipe covered in paint preventing complete examination.

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Play in steering rack inner joint(s) ()

Rear Body has slight corrosion cross member (6.1.B.2)

Steering system has slight free play detected at steering wheel (2.2.A.1b)

rear parking (secondary) brake imbalance requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.6b)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Rear fog lamp not working (1.3.2b)

Windscreen washer provides insufficient washer liquid (8.2.3)

Parking brake lever has little reserve travel (3.1.6b)

Offside Rear coil spring broken (2.4.C.1a)

Nail in offside rear tyre

Nearside Front Brake hose slightly deteriorated (3.6.B.4d)

Nearside Front Macpherson strut has slight play in the sliding bush or gland (2.5.B.1b)

Offside Front Brake hose slightly deteriorated (3.6.B.4d)

Offside Front Valve stem slightly damaged (4.1.D.1e)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

centre brake light lense damaged

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Nail in offside rear tyre

Nearside Front Brake hose slightly deteriorated (3.6.B.4d)

Nearside Front Macpherson strut has slight play in the sliding bush or gland (2.5.B.1b)

Offside Front Brake hose slightly deteriorated (3.6.B.4d)

Offside Front Valve stem slightly damaged (4.1.D.1e)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

centre brake light lense damaged

Offside Rear rear brake grabbing slightly (3.7.A.5b)

Nearside Rear coil spring incomplete (2.4.C.1a)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear rear brake grabbing slightly (3.7.A.5b)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Rear Brake pad(s) wearing thin (3.5.1g)

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Registration plate lamp not working (1.1.C.1d)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)