2006 Mazda Bongo

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Suspension component mounting repair covered in underseal fronts and rear (5.3.6 (a) (i))

Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Emissions unable to be completed due to exhaust leak (8.2.2.2 (e))

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Hydraulic fluid leaking excessively pipe under center of vehicle (8.4.1 (a) (i))

Nearside Battery insecure and likely to cause a short circuit (4.13 (a) (ii))

Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Behind sliding door (7.1.1 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i))

Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i))

Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i))

Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Spring mounting (5.3.6 (a) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Electrical wiring likely to touch hot or rotating parts Battery wire under bonnet (4.11 (a) (iii)) DANGEROUS

Rear Electrical wiring likely to drag on the ground fog light wire (4.11 (a) (iii)) DANGEROUS

Nearside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive Spring mount (5.3.6 (a) (i))

Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Rear Vehicle structure is corroded but structural rigidity is not significantly reduced Next to towing eye (6.1.1 (c) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced Rear chassis rails (6.1.1 (c) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement all bushes (5.3.4 (a) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement all bushes (5.3.4 (a) (i))

Offside Rear Upper Coil spring mounting corroded but not seriously weakened (5.3.1 (b) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Nearside Stop lamp(s) not working (4.3.1 (a) (ii))

Nearside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced Rear chassis rails (6.1.1 (c) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement all bushes (5.3.4 (a) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement all bushes (5.3.4 (a) (i))

Offside Rear Upper Coil spring mounting corroded but not seriously weakened (5.3.1 (b) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Lower arm in wheel arch (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Trailing arm mounting inner sill (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength trail arm mounting wheel arch (5.3.6 (a) (i))

Nearside Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i))

Nearside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement all bushes (5.3.4 (a) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement all bushes (5.3.4 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive Upper shock mount (5.3.6 (a) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced Rear chassis rails (6.1.1 (c) (i))

Nearside Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Outer Suspension component mounting prescribed area is corroded but not considered excessive Sill (5.3.6 (a) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i))

Nearside Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Nearside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Central Rear Upper Oil leak, but not excessive on engine (8.4.1 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced under body corroded (6.1.1 (c) (i))

Nearside Front Tyre worn close to legal limit/worn on edge on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge on edges (5.2.3 (e))

Offside Rear Outer Oil leak, but not excessive seal on axle (8.4.1 (a) (i))

Upper Integral body structure is corroded but structural rigidity is not significantly reduced body corroded (6.1.1 (c) (i))

Front Upper Driver's view of the road through the swept area of the windscreen materially affected by an obstruction plastic sun shade not see trough (3.1 (a) (ii))

Front Upper Electrical wiring insecure and in contact with sharp edges and rear (4.11 (a) (ii))

Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i))

Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i))

Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill hold (6.1.1 (c) (i))

Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under wheel arch holed (6.1.1 (c) (i))

Offside Rear Rear fog lamp not working (4.5.1 (a) (ii))

Nearside Rear Tyre tread depth below requirements of 1.6mm inner edge (5.2.3 (e)) DANGEROUS

Offside Front Electrical wiring likely to touch hot or rotating parts (4.11 (a) (iii)) DANGEROUS

Offside Rear Tyre tread depth below requirements of 1.6mm inner edge (5.2.3 (e)) DANGEROUS

Central Rear Upper Oil leak, but not excessive on engine (8.4.1 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced under body corroded (6.1.1 (c) (i))

Nearside Front Tyre worn close to legal limit/worn on edge on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge on edges (5.2.3 (e))

Offside Rear Outer Oil leak, but not excessive seal on axle (8.4.1 (a) (i))

Upper Integral body structure is corroded but structural rigidity is not significantly reduced body corroded (6.1.1 (c) (i))

n/s/f door locking/opening fault

o/s/r inner wheel arch corroded

parking brake lever high

n/s inner sill corroded and holed

Power steering pump has slight seepage (2.1.5 (a))

Nearside Rear Tyre worn close to legal limit/worn on edge below 3.mm and perished (5.2.3 (e))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis leg (5.3.6 (a) (i))

Offside Rear Tyre worn close to legal limit/worn on edge 1.6mm (5.2.3 (e))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Power steering pipe/hose has slight seepage pipes under bonnet (2.1.5 (a))

Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b))

Nearside Rear Anti-roll bar attachment bracket/mounting insecure broken (5.3.3 (a) (i))

Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Rear fog lamp not working (4.5.1 (a) (ii))

Windscreen washer provides insufficient washer liquid both (3.5 (a))

Nearside Rear Tyre worn close to legal limit/worn on edge below 3.mm and perished (5.2.3 (e))

Offside Headlamp aim too low (4.1.2 (a))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis leg (5.3.6 (a) (i))

Offside Rear Tyre worn close to legal limit/worn on edge 1.6mm (5.2.3 (e))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Power steering pipe/hose has slight seepage pipes under bonnet (2.1.5 (a))

Power steering pump has slight seepage (2.1.5 (a))

n/s inner sill corroded and holed

n/s/f door locking/opening fault

o/s/r inner wheel arch corroded

parking brake lever high

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Cross member (6.1.1 (c) (i))

Nearside Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Nearside Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill corroded (7.1.1 (a) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt inner (2.5.C.1a)

Nearside Front Seat belt anchorage prescribed area is corroded but not considered excessive To back seat belt mount areas. (5.2.6)

Nearside Rear Anti-roll bar linkage has slight play in a ball joint As Marked. (2.4.G.2)

Offside Front Seat belt anchorage prescribed area is corroded but not considered excessive To back outer sill areas (5.2.6)

Offside Registration plate lamp not working (1.1.C.1d)

Rear fog lamp tell tale not working (1.3.1b)

Nearside Rear Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Nearside Track rod end ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)

Offside Track rod end ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)

o/s/r sill corroded

Nearside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Oil leak

Spare wheel missing

Battery insecure (1.9.1)

Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Nearside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Nearside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Nearside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Oil leak

Spare wheel missing

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Nearside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Anti-roll bar attachment bracket/mounting fractured (2.4.G.1)

Offside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

surface rust on sills

Rear An item not tested (Manual)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

surface rust on sills

Offside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Nearside Inner Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Outer Rear Lower Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Offside Outer Rear Lower Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Offside Inner Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Obligatory mirror missing (8.1.1)

Registration plate lamp not working (1.1.5c)