2003 Mazda Bongo

Nearside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Offside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail (6.2.2 (d) (i))

Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced step assembly (6.1.1 (c) (i))

Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Offside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Nearside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Body component corroded and likely to cause injury sill corroded inner and outer (6.2.1 (a) (i))

Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch/footwell corroded (6.1.1 (c) (i))

Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail corroded and split (6.1.1 (c) (i))

Offside Body component corroded and likely to cause injury sill corroded inner and outer (6.2.1 (a) (i))

Offside Rear Body component corroded and likely to cause injury arch corroded (6.2.1 (a) (i))

Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear crossmember rotten/corroded (6.1.1 (c) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))

Rear crossmember corroded, tow bar is unusable

Vehicle structure is corroded but structural rigidity is not significantly reduced rear crossmember corroded (6.1.1 (c) (i))

Nearside Front Service brake excessively binding (1.2.1 (f))

Offside Front Service brake excessively binding (1.2.1 (f))

Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced rear crossmember corroded (6.1.1 (c) (i))

Central Exhaust has a major leak of exhaust gases mid section (6.1.2 (a))

Emissions unable to be completed major exhaust leak (8.2.2.2 (e))

Horn not working (7.7 (a))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Front Shock absorbers has a serious fluid leak (5.3.2 (b))

Nearside Headlamp lens seriously defective (4.1.1 (b) (ii))

Nearside Rear Other passenger door cannot be opened from outside the vehicle side door (6.2.3 (a))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i))

Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Front Brake pipe excessively corroded (1.1.11 (c))

Offside Headlamp lens seriously defective (4.1.1 (b) (ii))

Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c))

Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Windscreen washer not working (3.5 (a))

Nearside Front Shock absorbers has a reduced damping effect (5.3.2 (d))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Integral body structure is corroded but structural rigidity is not significantly reduced under sill, central (6.1.1 (c) (i))

Nearside Rear Suspension component mounting prescribed area damaged but not considered excessive chassis (5.3.6 (a) (i))

Nearside Windscreen damaged but not adversely affecting driver's view cracked (3.2 (a) (i))

Offside Front Service brake fluctuating, but not excessively (1.2.1 (e))

Offside Integral body structure is corroded but structural rigidity is not significantly reduced under sill central (6.1.1 (c) (i))

Offside Rear Suspension component mounting prescribed area damaged but not considered excessive chassis (5.3.6 (a) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))

Rear crossmember corroded

Nearside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced general area (6.1.1 (c) (i))

Offside Inner Vehicle structure is corroded but structural rigidity is not significantly reduced sill area (6.1.1 (c) (i))

Offside Outer Vehicle structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced general area (6.1.1 (c) (i))

Rear Vehicle structure is corroded but structural rigidity is not significantly reduced inner cross member both sides (6.1.1 (c) (i))

Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i))

Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front Steering component mounting prescribed area is excessively corroded (2.1.2 (e) (i))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i))

Nearside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced general area (6.1.1 (c) (i))

Offside Inner Vehicle structure is corroded but structural rigidity is not significantly reduced sill area (6.1.1 (c) (i))

Offside Outer Vehicle structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced general area (6.1.1 (c) (i))

Rear Inner Vehicle structure is corroded but structural rigidity is not significantly reduced cross member both sides (6.1.1 (c) (i))

Nearside Front Outer sill holed and corroded

Offside Front under sill holed and corroded

Offside Rear Service brake binding but not excessively (1.2.1 (f))

underbody and suspension components front and rear badly corroding

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing near suspension mount (5.3.6 (a) (i))

Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Rear Exhaust has a major leak of exhaust gases rear section missimg (6.1.2 (a))

Rear Spare wheel insecure in carrier (6.1.5 (b) (i))

Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i))

Rear Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Nearside Front Outer sill holed and corroded

Offside Front under sill holed and corroded

Offside Rear Service brake binding but not excessively (1.2.1 (f))

underbody and suspension components front and rear badly corroding

Nearside Front Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Coil spring corroded (5.3.1 (b) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Power steering component has slight seepage from a component Rack (2.1.5 (a))

Fuel system component leaking Injection pump (6.1.3 (b) (i))

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i))

Nearside Front Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Coil spring corroded (5.3.1 (b) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive Chassis (5.3.6 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Power steering component has slight seepage from a component Rack (2.1.5 (a))

Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Coil spring corroded Both (5.3.1 (b) (i))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced cill (6.1.1 (c) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Coil spring corroded Both (5.3.1 (b) (i))

Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g))

Horn sound not in accordance with requirements (7.7 (c))

Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x2 (5.3.6 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Coil spring corroded Both (5.3.1 (b) (i))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced cill (6.1.1 (c) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Rear Coil spring corroded Both (5.3.1 (b) (i))

Body has slight corrosion under body (6.1.B.2)

Nearside Front Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Offside Front Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Upper Body has slight corrosion (6.1.B.2)

excessive corrosion n/s and o/s rear outer wheel arch

Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill x2 (6.1.B.2)

Nearside Front Suspension arm has excessive play in a ball joint (2.4.G.2)

Offside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor/sill (6.1.B.2)

both rear wheel arches slightly corroded

Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill (6.1.B.2)

Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch (6.1.B.2)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Rear fog lamp not working (1.3.2b)

Nearside Front suspension ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Offside Front suspension ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front suspension ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Offside Front suspension ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Steering rack gaiter split (2.2.D.2d)

Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c)

Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

both headlamp patterns poor.

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Rear Exhaust system not adequately supported (7.1.1)

both headlamp patterns poor.

Rear Brake pad(s) wearing thin (3.5.1g)

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

front and rear discs worn

n/s/f anti roll bar link gaitors perishing

o/s/f anti roll bar link gaitors split

slight play in o/s/r anti-roll bar link bush

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Registration plate lamp not working (1.1.5c)

Nearside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Offside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)