1996 Fiat Ducato

Exhaust mounting defective various mounting rubbers splitting (6.1.2 (a))

Nearside Rear Tyre worn close to legal limit/worn on edge worn on outer edge (5.2.3 (e))

Offside Rear Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Rear Tyre slightly damaged/cracking or perishing cracking (5.2.3 (d) (ii))

Oil leak, but not excessive (8.4.1 (a) (i))

Play in steering rack inner joint(s)

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Shock absorbers has a slightly worn bush nearside & offside rear shock absorbers bushes deteriorated (5.3.2 (c))

Vehicle structure is corroded but structural rigidity is not significantly reduced front crossmember corroding (6.1.1 (c) (i))

Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis by front crossmember & engine mounting points (6.1.1 (c) (i))

Exhaust mounting defective various mounting rubbers splitting (6.1.2 (a))

Nearside Rear Tyre worn close to legal limit/worn on edge worn on outer edge (5.2.3 (e))

Offside Rear Tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Rear Tyre slightly damaged/cracking or perishing cracking (5.2.3 (d) (ii))

Oil leak, but not excessive (8.4.1 (a) (i))

Play in steering rack inner joint(s)

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Shock absorbers has a slightly worn bush nearside & offside rear shock absorbers bushes deteriorated (5.3.2 (c))

Vehicle structure is corroded but structural rigidity is not significantly reduced front crossmember corroding (6.1.1 (c) (i))

Coolant leak Header tank

Nearside Rear Lower Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Rear Lower Shock absorbers has a slightly worn bush (5.3.2 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. 35% (1.2.1 (b) (i))

Nearside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) DANGEROUS

Coolant leak Header tank

Exhaust mounting defective Rubber mounts broken/deteriorated (6.1.2 (a))

Nearside Rear Lower Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Rear Lower Shock absorbers has a slightly worn bush (5.3.2 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Exhaust has a major leak of exhaust gases Silencer (6.1.2 (a))

Horn not working (7.7 (a))

Nearside Front Shock absorbers has a serious fluid leak (5.3.2 (b))

Nearside Headlamp aim too low (4.1.2 (a))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Headlamp aim too low (4.1.2 (a))

Nearside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) DANGEROUS

Coolant leak Header tank

Exhaust mounting defective Rubber mounts broken/deteriorated (6.1.2 (a))

Nearside Rear Lower Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Rear Lower Shock absorbers has a slightly worn bush (5.3.2 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Front Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Front Exhaust has a minor leak of exhaust gases Before silencer (6.1.2 (a))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Cab steps insecure Slight corrosion (6.2.8 (a) (i))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Parking brake imbalance.

Rear Brake pipe corroded, covered in grease or other material Both (1.1.11 (c))

Rear Service brake binding but not excessively Both (1.2.1 (f))

Rear Shock absorbers has a slightly worn bush Both (5.3.2 (c))

Some underbody corrosion covered in underseal

Vehicle structure is corroded but structural rigidity is not significantly reduced General underbody corrosion. (6.1.1 (c) (i))

Offside Parking brake inoperative on one side (1.4.1 (a))

Service brake efficiency below requirements (1.2.2 (a) (i))

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

Front Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Front Exhaust has a minor leak of exhaust gases Before silencer (6.1.2 (a))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Cab steps insecure Slight corrosion (6.2.8 (a) (i))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Parking brake imbalance.

Rear Brake pipe corroded, covered in grease or other material Both (1.1.11 (c))

Rear Service brake binding but not excessively Both (1.2.1 (f))

Rear Shock absorbers has a slightly worn bush Both (5.3.2 (c))

Some underbody corrosion covered in underseal

Vehicle structure is corroded but structural rigidity is not significantly reduced General underbody corrosion. (6.1.1 (c) (i))

Battery insecure and likely to cause a short circuit (4.13 (a) (ii))

Brake cable guide defective and affecting operation seized (1.1.15 (d))

Exhaust system insecure (6.1.2 (a))

Front Electrical wiring insecure and in contact with sharp edges under rad (4.11 (a) (ii))

Fuel cap/sealing device ineffective (6.1.3 (b) (i))

Nearside Front Headlamp insecure (4.1.1 (c))

Nearside Headlamp aim too low (4.1.2 (a))

Nearside Rear Service brake excessively binding (1.2.1 (f))

Offside Headlamp aim too low (4.1.2 (a))

Offside Rear Service brake excessively binding (1.2.1 (f))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

Brake fluid warning lamp illuminated (1.1.10 (f))

Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Front Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Front Lower Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security under rad (6.2.2 (d) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Inner Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Nearside Front Inner Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security wing (6.2.2 (d) (i))

Nearside Front Obligatory indirect vision device slightly damaged (3.3 (b) (i))

Nearside Front Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security chassis rail (6.2.2 (d) (i))

Nearside Rear Inner Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Front Inner Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Offside Front Lower Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security step (6.2.2 (d) (i))

Offside Front Service brake binding but not excessively (1.2.1 (f))

Offside Front Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security chassis rail (6.2.2 (d) (i))

Offside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))

All direction indicators not working (4.4.1 (a) (ii))

Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced doorstep/sill (7.1.1 (a) (i))

Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i))

Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Stop lamp(s) all not working (4.3.1 (a) (iii)) DANGEROUS

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))

Central Exhaust mounting defective (6.1.2 (a))

Nearside Front Seat belt anchorage prescribed area is corroded but not considered excessive doorstep/sill (7.1.1 (a) (i))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Registration plate lamp missing in the case of multiple lamps or light sources (4.7.1 (b) (i))

Front Brakes imbalanced across an axle Axle 1 (1.2.1 (b) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i))

Nearside Headlamp aim too low (4.1.2 (a))

Offside Front Service brake lagging in operation (1.2.1 (d))

Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i))

Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Service brake efficiency below requirements (1.2.2 (a) (i))

Central Exhaust mounting defective (6.1.2 (a))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Seat belt anchorage prescribed area is corroded but not considered excessive doorstep/sill (7.1.1 (a) (i))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Service brake binding but not excessively (1.2.1 (f))

Offside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Registration plate lamp missing in the case of multiple lamps or light sources (4.7.1 (b) (i))

Front Brakes imbalanced across an axle Axle 1 (1.2.1 (b) (i))

Nearside Front Headlamp aim too low (4.1.2 (a))

Nearside Front Shock absorbers has negligible damping effect (5.3.2 (d))

Nearside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Exhaust mounting defective several mounts missing (6.1.2 (a))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Service brake binding but not excessively (1.2.1 (f))

Offside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Nearside Rear fog lamp not working (4.5.1 (a) (ii))

Offside Rear fog lamp not working (4.5.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Stop lamp(s) all not working (4.3.1 (a) (iii)) DANGEROUS

Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Horn not working (7.7 (a) (ii))

Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting step (6.2.2 (d) (i))

Offside Front Brake hose porous (1.1.12 (e))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rear of step (6.2.2 (d) (i))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting step (6.2.2 (d) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Brake pipe corroded, covered in grease or other material various (1.1.11 (c))

Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

All outline marker lamps not working both (4.2.1 (a))

Headlamp levelling device inoperative (4.1.5 (a))

Horn not working (7.7 (a) (ii))

Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut (5.3.6 (a) (i))

Offside Headlamp light intensity severely reduced (4.1.4 (a))

Power steering pipe/hose excessively corroded (2.1.5 (g) (i))

Rear Brake cable damaged (1.1.15 (a))

Rear fog lamp not working (4.5.1 (a) (ii))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Windscreen wiper does not clear the windscreen effectively both (3.4 (b) (ii))

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

Brake pipe corroded, covered in grease or other material various (1.1.11 (c))

Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Front end rusty has been sealed

Nearside Rear Rear position lamp(s) deteriorated, but still visible from a reasonable distance (1.1.A.3d)

Offside Front brake very slight binding

exhaust rusty

radiator mounts worn

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside rear brake binding (3.7.B.1)

Offside rear brake binding (3.7.B.1)

Front end rusty has been sealed

Nearside Rear Rear position lamp(s) deteriorated, but still visible from a reasonable distance (1.1.A.3d)

exhaust rusty

radiator mounts worn

exhaust rusty

slight oil leak

surface rust on all brake discs

Offside Front Lower outer sill rusty

Offside Front innerwing materialy weakend through excessive corrosion

Offside Front wheel bearing has slight play (2.5.A.3c)

nearside and offside lower under sills to outer sill materialy weak

oil leak

Exhaust system not adequately supported rubber mounts missing (7.1.1)

Nearside Front Upper Suspension component mounting prescribed area is excessively corroded turret area (2.4.A.3)

Offside Front Brake pipe excessively corroded from master cylinder (3.6.B.2c)

Offside Registration plate lamp not working (1.1.C.1d)

Offside Windscreen washer provides insufficient washer liquid (8.2.3)

Power steering pipe(s) or hose(s) excessively corroded on steering rackj (2.3.2)

Offside Front Lower outer sill rusty

Offside Front innerwing materialy weakend through excessive corrosion

Offside Front wheel bearing has slight play (2.5.A.3c)

nearside and offside lower under sills to outer sill materialy weak

oil leak

Brake hose has slight corrosion to ferrules (3.6.B.4e)

Brake pipe slightly corroded (3.6.B.2c)

Front wheel bearing has slight play (2.5.A.3c)

Power steering pipe(s) or hose(s) slightly corroded (2.3.2)

Vehicle structure has slight corrosion (6.1.A.1)

Exhaust system not adequately supported (7.1.1)

Horn not working (1.6.2a)

Brake hose has slight corrosion to ferrules (3.6.B.4e)

Brake pipe slightly corroded (3.6.B.2c)

Front wheel bearing has slight play (2.5.A.3c)

Power steering pipe(s) or hose(s) slightly corroded (2.3.2)

Vehicle structure has slight corrosion (6.1.A.1)

Brake pipe slightly corroded (3.6.B.2c)

O/S/F chassis heverley coroded O/S 30 cm

Power steering pipe(s) or hose(s) slightly corroded (2.3.2)

corossion O/S 30 cm lower seat belt mountings

An item not tested (Manual)

Battery insecure (1.9.1)

Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Nearside Headlamp insecure (1.7.3)

Offside Front Lower Brake pipe excessively corroded (3.6.B.2c)

Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Upper Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Parking brake: efficiency below requirements (3.7.B.7)

Windscreen washer provides insufficient washer liquid (8.2.3)

Brake pipe slightly corroded (3.6.B.2c)

O/S/F chassis heverley coroded O/S 30 cm

Power steering pipe(s) or hose(s) slightly corroded (2.3.2)

corossion O/S 30 cm lower seat belt mountings

Nearside Front Upper Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Upper Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front wheel bearing has slight play (2.5.A.3c)

nearside lower step,upper step ,offside upper step holed through rust

offside front chassis materialy weakend through excessive corrosion

offside front outriger/wheelarch are materialy weak

offside lower crossmember holed

Exhaust system not adequately supported (7.1.1)

Front registration plate deteriorated (6.3.1d)

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Headlamp not working on dipped beam (1.7.5a)

Nearside Rear Lower Body has a sharp edge caused by damage (6.1.C.1)

Offside Front Lower Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Headlamp aim too low (1.8)

Power steering pipe(s) or hose(s) excessively corroded (2.3.2)

Nearside Front Upper Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Upper Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front wheel bearing has slight play (2.5.A.3c)

nearside lower step,upper step ,offside upper step holed through rust

offside front chassis materialy weakend through excessive corrosion

offside front outriger/wheelarch are materialy weak

offside lower crossmember holed

Centre Brake pipe slightly corroded (3.6.B.2c)

Centre Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

offside front crossmember holed through excessive corrosion

offside front inner wing holed through excessive corrosion

offside front sill step hold

oil leak

power steering pipes rusty

Horn not working (1.6.2a)

Nearside Headlamp aim too high (1.8)

Offside Front Upper Brake pipe excessively corroded (3.6.B.2c)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Registration plate lamp not working (1.1.C.1d)

Parking brake: efficiency below requirements (3.7.B.7)

Nearside Rear Brake hose bulging under pressure (3.6.B.3) DANGEROUS

Centre Brake pipe slightly corroded (3.6.B.2c)

Centre Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Offside Rear Brake hose has slight corrosion to ferrules (3.6.B.4e)

offside front crossmember holed through excessive corrosion

offside front inner wing holed through excessive corrosion

offside front sill step hold

oil leak

power steering pipes rusty

offside front lower wing area rusty

power steering pipes rusty

Front An item not tested (Manual)

Nearside Front Lower Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Seat belt damaged sufficient to obstruct correct operation of the belt (5.2.2a)

Nearside Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside rear brake binding (3.7.B.1)

Offside Front Lower Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Windscreen washer provides insufficient washer liquid (8.2.3)

Rear Lower Exhaust mounting missing (7.1.1b)

offside front lower wing area rusty

power steering pipes rusty

Oil leak

offside front inner wing(upper and lower)materialy weakend through excessive corrosion not within a prescribed area

offside front step to sill area rusty considerd not excessive

Offside Front Upper Front position lamp(s) not working (1.1.A.3b)

Upper Rear position lamp(s) excessively deteriorated so that it is not visible from a reasonable distance (1.1.A.3d)

Oil leak

exhaust mount rubbers perrished

offside front inner wing(upper and lower)materialy weakend through excessive corrosion not within a prescribed area

offside front step to sill area rusty considerd not excessive

Emissions not tested (7.0)

Exhaust has a major leak of exhaust gases (7.1.2)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

Nearside Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a)

Nearside Headlamp not in a clean condition affecting beam image (1.2.4a)

Nearside Rear Suspension has inadequate clearance with the bump stop (2.4.A.1a)

Offside Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a)

Offside Headlamp not working on dipped beam (1.7.5a)

Parking brake: efficiency below requirements (3.7.B.7)

Windscreen wiper does not clear the windscreen effectively (8.2.2)

Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

slight play in both rear radious arms

Front registration plate deteriorated (6.3.1d)

Horn not working (1.6.2a)

Nearside Rear Lower Shock absorber has an excessively worn bush (2.7.4)

Nearside Rear Service brake grabbing severely (3.7.C.2)

Nearside Rear Upper All position lamps not working (1.1.A.3b)

Nearside Stop lamp not working (1.2.1b)

Offside Front Upper All position lamps not working (1.1.A.3b)