2003 Mazda Bongo

Offside Front Lower Panel Assembly Corroded

Emissions unable to be completed (8.2.2.2 (e))

Exhaust has a major leak of exhaust gases hole in silencer (6.1.2 (a))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing strut top area and at front (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger front face behind plastic trim (5.3.6 (a) (i))

Nearside Headlamp aim too low (4.1.2 (a))

Nearside Rear Passenger's seat backrest cannot be secured in the upright position. (6.2.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i))

Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting corner (6.1.6 (i) (i))

Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing strut top area and at front (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger front face behind plastic trim (5.3.6 (a) (i))

Offside Headlamp aim too low (4.1.2 (a))

Offside Rear Passenger's seat backrest cannot be secured in the upright position. (6.2.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i))

Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting corner (6.1.6 (i) (i))

Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Offside Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Nearside Front Shock absorbers has a reduced damping effect (5.3.2 (d))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Side repeater slightly discoloured (4.4.3 (a))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Lower Suspension arm pin or bush worn but not resulting in excessive movement front bush, both sides (5.3.4 (a) (i))

Rear Shock absorbers has light misting of oil both sides (5.3.2 (b))

Vehicle structure is corroded but structural rigidity is not significantly reduced general underside corrosion (6.1.1 (c) (i))

Nearside Rear Outer Tyre has a cut but not deep enough to reach the ply or cords sidewall (5.2.3 (d) (i))

Power steering component has slight seepage from a component (2.1.5 (a))

Nearside Headlamp aim too low (4.1.2 (a))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills (5.3.6 (a) (i))

Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i))

Offside Headlamp aim too low (4.1.2 (a))

Offside Rear fog lamp not working (4.5.1 (a) (ii))

Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Nearside Rear Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security inner sill at rear (6.2.2 (d) (i))

Nearside Rear Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Nail in tyre ()

Offside Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security inner sill at rear (6.2.2 (d) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Power steering component has slight seepage from a component rack seal (2.1.5 (a))

Windscreen damaged but not adversely affecting driver's view top (3.2 (a) (i))

under vehicle corroded ( body, suspension etc )

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security inner sill at rear (6.2.2 (d) (i))

Nearside Rear Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Nail in tyre ()

Offside Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security inner sill at rear (6.2.2 (d) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Power steering component has slight seepage from a component rack seal (2.1.5 (a))

Windscreen damaged but not adversely affecting driver's view top (3.2 (a) (i))

under vehicle corroded ( body, suspension etc )

Rear fog lamp missing (4.5.1 (a) (ii))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Rear Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Nearside Rear Tyre slightly damaged/cracking or perishing perished (5.2.3 (d) (ii))

Offside Front Nail in tyre ()

Offside Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security inner sill (6.2.2 (d) (i))

Oil leak, but not excessive engine (8.4.1 (a) (i))

Power steering component has slight seepage from a component rack (2.1.5 (a))

Windscreen damaged but not adversely affecting driver's view nearside small crack (3.2 (a) (i))

under vehicle corroded ( suspension, body etc )

Nearside Body has slight corrosion sill (6.1.B.2)

Nearside Rear tyre deteriorated side wall

Offside Body has slight corrosion sill (6.1.B.2)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

near side and off side rear wheel arch under sealed

Nearside Rear Seat belt anchorage prescribed area is excessively corroded wheel arch (5.2.6)

Offside Rear Seat belt anchorage prescribed area is excessively corroded wheel arch (5.2.6)

Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed (6.1.B.2)

Rear fog lamp missing (1.3.2a)

Nearside Vehicle structure has slight corrosion sill (6.1.B.2)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Vehicle structure has slight corrosion sill (6.1.B.2)

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

Vehicle structure has slight corrosion (6.1.B.2)

Exhaust has a major leak of exhaust gases (7.1.2)

Offside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch (2.4.A.3)

Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)

Offside Front Inner sill

Nearside Outer Seat belt anchorage prescribed area is corroded but not considered excessive sill (5.2.6)

Nearside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive wheel arch (2.4.A.3)

Offside Inner Suspension component mounting prescribed area is corroded but not considered excessive sill (2.4.A.3)

Offside Inner Suspension component mounting prescribed area is corroded but not considered excessive sill (2.4.A.3)

Offside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Outer Seat belt anchorage prescribed area is corroded but not considered excessive sill (5.2.6)

Offside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive wheel arch (2.4.A.3)

Anti-lock braking system warning lamp does not illuminate (3.4.1b)

Nearside Front Inner Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)

Nearside Headlamp aim too low (1.8)

Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Stop lamp not working (1.2.1b)

Offside Front Anti-lock braking system wiring excessively damaged (3.4.3)

Offside Front Anti-lock braking system wiring excessively damaged (3.4.3)

Offside Headlamp aim too low (1.8)

Offside Steering rack gaiter split (2.2.D.2d)

Offside Windscreen wiper blade insecure (8.2.2)

Rear Vehicle structure excessively corroded within 30cm of towbar mounting crossmember (6.6.6)

Nearside Outer Seat belt anchorage prescribed area is corroded but not considered excessive sill (5.2.6)

Nearside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive wheel arch (2.4.A.3)

Offside Inner Suspension component mounting prescribed area is corroded but not considered excessive sill (2.4.A.3)

Offside Inner Suspension component mounting prescribed area is corroded but not considered excessive sill (2.4.A.3)

Offside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Outer Seat belt anchorage prescribed area is corroded but not considered excessive sill (5.2.6)

Offside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive wheel arch (2.4.A.3)

Items removed from driver's view prior to test

Offside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Body has a sharp edge caused by corrosion (6.1.C.1)

Offside Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Inner Front constant velocity joint is insecure (2.5.C.1b)

Offside Inner Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Inner Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Inner Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Items removed from driver's view prior to test

Offside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

corrosion off side inner rear

Nearside Front Headlamp not working on dipped beam (1.7.5a)

Nearside Steering rack gaiter split (2.2.D.2d)

Offside Rear Direction indicator not working (1.4.A.2c)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Steering rack gaiter split (2.2.D.2d)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

corrosion off side inner rear

spare tyre clse to legal limit

Offside Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Outer Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Inner Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nail in offside front tyre

Nearside Outer Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)

Offside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Outer Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Centre Rear Exhaust system not adequately supported (7.1.1)

Offside Rear Anti-roll bar attachment bracket/mounting fractured (2.4.G.1)

Offside Rear fog lamp missing (1.3.2a)

Windscreen washer provides insufficient washer liquid (8.2.3)

Front Brake pad(s) wearing thin (3.5.1g)

Nail in offside front tyre

Nearside Outer Seat belt anchorage prescribed area is distorted but not considered excessive (5.2.6)

Offside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Outer Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

front brake pads wearing thin

o/s/f tyre worn to 2mm on inner edge

rear seats not in use

slight oil leak on engine

slight weep from o/s/f cv boot

unable to check rear tyres + wheel bearings properly due to 4WD

Power steering pipe(s) or hose(s) has slight seepage (2.3.3b)