2008 Ford Ka

Brakes imbalanced across an axle (1.2.1 (b) (i))

Nearside Front Floor excessively deteriorated (6.2.4 (a) (i))

Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii))

Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i))

Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Nearside Rear Axle has excessive vertical movement between stub axle and axle beam (5.1.2 (c) (i))

Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Offside Front Floor excessively deteriorated (6.2.4 (a) (i))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Front Brakes imbalanced across an axle by more than 50% Axle 1 (1.2.1 (b) (ii)) DANGEROUS

Offside Rear Axle has excessive vertical movement between stub axle and axle beam such that directional stability is impaired (5.1.2 (c) (ii)) DANGEROUS

Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Sub-frame pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Rear Sub-frame pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Fuel hose insecure (7.2.1)

Nail in offside rear tyre

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)