2003 Hyundai Getz

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Front Service brake imbalanced across an axle (1.2.1 (b) (i))

Headlamp lens seriously defective (4.1.1 (b) (ii))

Nearside Front Brake hose ferrule excessively corroded (1.1.12 (f) (i))

Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Rear Brake hose ferrule excessively corroded (1.1.12 (f) (i))

Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch/sill (5.3.6 (a) (i))

Offside Front Brake hose ferrule excessively corroded (1.1.12 (f) (i))

Offside Rear Service brake excessively binding (1.2.1 (f))

Sub-frame corroded and seriously weakened (5.3.3 (b) (i))

Brake pipe leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) DANGEROUS

Nearside Rear Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Offside Front Sub-frame attachment bracket/mounting likely to fail (5.3.3 (b) (ii)) DANGEROUS

Nearside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Offside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Rear Brake pipe inadequately clipped or supported (1.1.11 (d) (i))

all suspension components corroded

Rear underbody rust non-excessive

Front brake disc BackPlate excessive rust

Front Brake disc contaminated (1.1.14 (b))

Front Headlamp lens seriously defective (4.1.1 (b) (ii))

Front Sub-frame corroded and seriously weakened (5.3.3 (b) (i))

Front Windscreen wiper does not clear the windscreen effectively Both (3.4 (b) (ii))

Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Rear Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Front Headlamp lens seriously defective both (4.1.1 (b) (ii))

Front Sub-frame corroded and seriously weakened (5.3.3 (b) (i))

Front Windscreen wiper does not clear the windscreen effectively both (3.4 (b) (ii))

Offside Front Brake pipe at imminent risk of failure or fracture (1.1.11 (a)) DANGEROUS

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Brake performance not tested (1.2.1 (g))

Brake pipe excessively corroded both short pipes to junctions(front to rear) (1.1.11 (c))

Brake pipe leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) DANGEROUS

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Brake pipe slightly corroded front to rear (3.6.B.2c)

Offside Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Nearside Front Brake pipe slightly corroded (3.6.B.2c)

Brake pipe slightly corroded (3.6.B.2c)

Nearside Brake pipe slightly corroded (3.6.B.2c)

Exhaust has a major leak of exhaust gases (7.1.2)

Exhaust tailpipe not capable of allowing the emission probe to be inserted (7.3.D.1)

Brake pipe slightly corroded (3.6.B.2c)

Nearside Brake pipe slightly corroded (3.6.B.2c)

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Front Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)