2001 Subaru Impreza

Nearside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Oil leak, but not excessive ROCKER COVERS (8.4.1 (a) (i))

Nearside Front Headlamp aim too low (4.1.2 (a))

Nearside Front Lower Steering locking device missing Ball joint castle headed securing nut split pin missing (2.1.3 (d))

Offside Front Lower Steering locking device missing Ball joint securing castle headed nut split pin missing (2.1.3 (d))

Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Rear Upper Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Oil leak, but not excessive (8.4.1 (a) (i))

Offside Front Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Front Oil leak, but not excessive (8.4.1 (a) (i))

Offside Front Inner Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Brake performance not tested (1.2.1 (g))

Nearside Rear Suspension arm pin or bush excessively worn trailing arm at body (5.3.4 (a) (i))

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch/ end of sill (5.3.6 (a) (i))

Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Nearside Front Valve stem seriously damaged (5.2.3 (j)) DANGEROUS

Offside Front Valve stem seriously damaged (5.2.3 (j)) DANGEROUS

Nearside Front Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive arch/ end of sill (5.3.6 (a) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Rear Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Rear Brake pipe corroded, covered in grease or other material all to junction block (1.1.11 (c))

Offside Rear Child Seat fitted not allowing full inspection of adult belt ()

Offside Rear Shock absorber has a light misting of oil (2.7.3)

Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Rear Brake pad(s) wearing thin (3.5.1g)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Headlamp not in good working order adversely affecting beam image (1.2.4a)

Nearside Registration plate lamp not illuminating the registration plate (1.1.C.1e)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Registration plate lamp not working (1.1.5c)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)