2002 Subaru Forester

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Nearside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Rear Upper Integral body structure is corroded but structural rigidity is not significantly reduced strut mounting area (6.1.1 (c) (i))

Nearside mirror back insecure

Offside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear light lens broken

Subframe mounting prescribed area is corroded but not considered excessive all rear beam mountings (5.3.6 (a) (i))

Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

corrosion at under body of vehicle

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Rear Anti-roll bar missing (5.3.3 (a) (ii)) DANGEROUS

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front registration plate deteriorated but not likely to be misread damaged (6.3.1d)

Rear Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)

Rear Shock absorber has a light misting of oil both sides (2.7.3)

Rear tyres miss shaped slightly

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Front Lower Ball joint dust cover deteriorated, but preventing the ingress of dirt both sides (2.2.C.1c)

Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Offside Rear Shock absorber has a light misting of oil (2.7.3)

Rear Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Vehicle structure has slight corrosion (6.1.A.1)

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

both rear tyres slightly out of shape

minor oil leaks

plastic sill trims and under trays fitted

Front Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)

Front Lower Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt both sides (2.4.G.2)

Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front Road wheel slightly damaged (4.2.A.1a)

Rear Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement both sides (2.4.G.2)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Vehicle structure has slight corrosion (6.1.A.1)

all rear driveshaft boots deteriorated

minor oil leaks

under trays and plastic sill trims fitted

Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Nearside Stop lamp not working (1.2.1b)

Nearside Windscreen washer provides insufficient washer liquid (8.2.3)

Offside Stop lamp not working (1.2.1b)

Offside Windscreen washer provides insufficient washer liquid (8.2.3)

Front Brake pad(s) less than 1.5 mm thick both sides (3.5.1g) DANGEROUS

Front Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)

Front Lower Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt both sides (2.4.G.2)

Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front Road wheel slightly damaged (4.2.A.1a)

Rear Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement both sides (2.4.G.2)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Vehicle structure has slight corrosion (6.1.A.1)

all rear driveshaft boots deteriorated

minor oil leaks

under trays and plastic sill trims fitted

Front Lower Ball joint dust cover deteriorated, but preventing the ingress of dirt both sides (2.2.C.1c)

Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Vehicle structure has slight corrosion (6.1.A.1)

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

offside rear wheel bearing slightly noisy

plastic covers fitted and undertrays fitted

underside of vehicle becoming to dirty to test

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Front Lower Ball joint dust cover deteriorated, but preventing the ingress of dirt both sides (2.2.C.1c)

Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Vehicle structure has slight corrosion (6.1.A.1)

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

plastic covers fitted and undertrays fitted

underside of vehicle becoming to dirty to test

Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Front Lower Ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Road wheel with a slightly distorted bead rim (4.2.A.1a)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Under-trays fitted obscuring some underside components

Vehicle structure has slight corrosion (6.1.A.1)

Vehicle's internal headlight adjuster altered to recheck lights

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

all rear driveshaft boots deteriorated at time of test

exhaust system deteriorated at time of test

unable to fully inspect both outer body sills due to plastic covers fitted to vehicle at time of test

Nearside Rear Brake hose ferrule excessively corroded (3.6.B.4e)

Offside Rear Brake hose ferrule excessively corroded (3.6.B.4e)

Centre Brake pipe excessively corroded (3.6.B.2c) DANGEROUS

Nearside Inner Rear Brake pipe excessively corroded (3.6.B.2c) DANGEROUS

Offside Inner Rear Brake pipe excessively corroded (3.6.B.2c) DANGEROUS

Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Front Lower Ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Road wheel with a slightly distorted bead rim (4.2.A.1a)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Under-trays fitted obscuring some underside components

Vehicle structure has slight corrosion (6.1.A.1)

Vehicle's internal headlight adjuster altered to recheck lights

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

all rear driveshaft boots deteriorated at time of test

exhaust system deteriorated at time of test

unable to fully inspect both outer body sills due to plastic covers fitted to vehicle at time of test

Centre Rear Brake pipe slightly corroded (3.6.B.2c)

Front Brake hose has slight corrosion to ferrules (3.6.B.4e)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Non obligatory mirror damaged

Rear Brake hose has slight corrosion to ferrules (3.6.B.4e)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Under-trays fitted obscuring some underside components

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

exhaust system deteriorated at time of test

unable to fully inspect both outer body sills due to plastic covers fitted to vehicle at time of test

Body has slight corrosion (6.1.B.2)

Brake hose slightly deteriorated (3.6.B.4d)

Brake pipe slightly corroded (3.6.B.2c)

Engine covers fitted obscuring some components in the engine bay

Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Front Brake pad(s) wearing thin (3.5.1g)

Front Shock absorber has a slightly reduced damping effect (2.7.5)

Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Rear Shock absorber has a slightly reduced damping effect (2.7.5)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Under-trays fitted obscuring some underside components

Vehicle structure has slight corrosion (6.1.A.1)

the underneath of the vehicle was becoming so dirty that a full inspection was made very hard to carry out.

un able to fully inspect outer body sills due to plastic trims / gaurds fitted at the time of test.

Centre Rear Brake pipe slightly corroded (3.6.B.2c)

Exhaust has part of the system slightly deteriorated (7.1.1a)

Front Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Front Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Front Road wheel with a slightly distorted bead rim (4.2.A.1a)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

the underneath of the vehicle is becoming dirty so that a full inspection was made very hard.

un-able to fully inspect outer body sills due to plastic trims fitted at the time of test

Centre Rear Brake pipe slightly corroded (3.6.B.2c)

Exhaust has part of the system slightly deteriorated (7.1.1a)

Front Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Front Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Front Road wheel with a slightly distorted bead rim (4.2.A.1a)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

the underneath of the vehicle is becoming dirty so that a full inspection was made very hard.

un-able to fully inspect outer body sills due to plastic trims fitted at the time of test

Centre Brake pipe slightly corroded (3.6.B.2c)

Exhaust has part of the system slightly deteriorated (7.1.1a)

rear drive shaft boots deteriorated

unable to fully inspect both outer body sills due to plastic covers fitted to vehicle at time of test

Nearside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Offside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Nearside Front Brake pad(s) less than 1.5 mm thick (3.5.1g) DANGEROUS

Nearside Front brake disc in such a condition that it is seriously weakened (3.5.1i) DANGEROUS

Centre Brake pipe slightly corroded (3.6.B.2c)

Exhaust has part of the system slightly deteriorated (7.1.1a)

rear drive shaft boots deteriorated

unable to fully inspect both outer body sills due to plastic covers fitted to vehicle at time of test

Brake pipe slightly corroded (3.6.B.2c)

Exhaust has a minor leak of exhaust gases (7.1.2)

Exhaust has part of the system slightly deteriorated (7.1.1a)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

all metal brake pipes are covered in plastic or sealer so a full inspection was not possable

un-able to fully inspect outer body sills due to plastic trims / gaurds fitted at the time of test

Brake pipe slightly corroded (3.6.B.2c)

Exhaust has a minor leak of exhaust gases (7.1.2)

Exhaust has part of the system slightly deteriorated (7.1.1a)

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Rear Wheel nut(s) loose (4.2.A.1e)

Offside Headlamp aim too high (1.8)

Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

all metal brake pipes are covered in plastic or sealer so a full inspection was not possable

un-able to fully inspect outer body sills due to plastic trims / gaurds fitted at the time of test