2011 Honda Cr-z

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Macpherson strut corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Shock absorbers has slight external damage to the casing corroded (5.3.2 (b))

Offside Front Macpherson strut corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Rear Shock absorbers has slight external damage to the casing corroded (5.3.2 (b))

Suspension arm corroded but not seriously weakened rear axle (5.3.3 (b) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan (5.3.6 (a) (i))

Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i))

Offside Front Road wheel fixing missing wheel nut missing (5.2.1 (a) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Macpherson strut corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Shock absorbers has slight external damage to the casing corroded (5.3.2 (b))

Offside Front Macpherson strut corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Rear Shock absorbers has slight external damage to the casing corroded (5.3.2 (b))

Suspension arm corroded but not seriously weakened rear axle (5.3.3 (b) (i))

Front Registration plate does not conform to the specified requirements (0.1 (d))

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Rear Registration plate does not conform to the specified requirements (0.1 (d))

Registration plate inscription missing both (0.1 (b))

Front Suspension arm pin or bush worn but not resulting in excessive movement Both rear bushes (5.3.4 (a) (i))

Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Brake pad(s) wearing thin BOTH REAR INSIDE (1.1.13 (a) (ii))

Tyre tread depth below requirements of 1.6mm BOTH FRONT (5.2.3 (e)) DANGEROUS

Brake pad(s) wearing thin BOTH REAR INSIDE (1.1.13 (a) (ii))

NEARSIDE REAR BRAKE BACKPLATE INSECURE AND FOULING WHEEL

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Offside Rear Service brake binding but not excessively (1.2.1 (f))

Heat shield around front cat badly corroded

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement wishbone arm rear bush (2.4.G.2)

Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Under-trays fitted obscuring some underside components