2007 Ford Freda

Manufactures engine and body covers fitted restricting full inspection

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

under side of vehicle coated in under seal restricting inspection of body/chassis and pipes

Emissions unable to be completed over heating (8.2.2.2 (e))

Manufactures engine and body covers fitted restricting full inspection

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

under side of vehicle coated in under seal restricting inspection of body/chassis and pipes

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Power steering component has slight seepage from a component rack (2.1.5 (a))

Rear Exhaust mounting defective (6.1.2 (a))

all underside of vehicle including various repairs coated in underseal

no rear seats fitted time of test

Headlamp aim unable to be tested (4.1.2 (b))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i))

Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Nearside Headlamp not working on main beam (4.1.1 (a) (ii))

Nearside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chasse leg (5.3.6 (a) (i))

Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i))

Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chasse leg (5.3.6 (a) (i))

Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i))

Rear fog lamp does not emit a steady red light (4.5.4 (a))

Registration plate lamp does not illuminate simultaneously with the position lamps (4.7.2 (a))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Power steering component has slight seepage from a component rack (2.1.5 (a))

Rear Exhaust mounting defective (6.1.2 (a))

all underside corroded

no rear seats fitted time of test

underside wax oiled

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Power steering component has slight seepage from a component steering rack (2.1.5 (a))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Exhaust mounting defective (6.1.2 (a))

several underside repairs covered in underseal

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Brake performance not tested battery insecure (1.2.1 (g))

Emissions not tested (8.2.2.2 (e))

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Lower Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear bolt mounting point inner wheel arch (5.3.6 (a) (i))

Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member mounting (5.3.6 (a) (i))

Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i))

Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member mounting (5.3.6 (a) (i))

Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii))

Power steering component leaking rack area (2.1.5 (a))

Power steering inoperative (2.1.5 (c) (i))

Rear fog lamp switch inoperative (4.5.3 (a))

Brake disc worn, pitted or scored, but not seriously weakened both rears (1.1.14 (a) (ii))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Manufactures engine and body covers fitted restricting full inspection

Nearside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Nearside Seat belt anchorage prescribed area is corroded but not considered excessive inner and outer sills (7.1.1 (a) (i))

Nearside Steering rack has slight free play detected at steering wheel (2.3 (a) (i))

Nearside Suspension component mounting prescribed area is corroded but not considered excessive front and rear (5.3.6 (a) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))

Offside Rear Brake pipe corroded, covered in grease or other material over tank (1.1.11 (c))

Offside Seat belt anchorage prescribed area is corroded but not considered excessive inner and outer sills (7.1.1 (a) (i))

Offside Steering rack has slight free play detected at steering wheel (2.3 (a) (i))

Offside Suspension component mounting prescribed area is corroded but not considered excessive front and rear (5.3.6 (a) (i))

Offside Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Service brake binding but not excessively both rears (1.2.1 (f))

Steering column top bearing slightly worn (2.2.2 (b))

Steering rack has slight free play detected at steering wheel (2.3 (a) (i))

Underside coated in wax oil restricting full inspection of body suspension and brake pipes

rear axle corroded including mounting brackets

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Battery insecure and likely to fall from carrier Both batteries (4.13 (a) (ii))

Brake performance not tested Batteries insecure unsafe to test (1.2.1 (g))

Emissions not tested insufficient oil (8.2.2.2 (e))

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Cross member lower corner (5.3.6 (a) (i))

Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i))

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords 195/70/15C (5.2.3 (d) (i))

Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Numerous holes inner & outer sill , Upper inner wheel arch (5.3.6 (a) (i))

Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Cross member lower corner (5.3.6 (a) (i))

Power steering component leaking Steering rack leaking (2.1.5 (a))

Power steering inoperative (2.1.5 (c) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Steering wheel has movement relative to the column indicating looseness (2.2.1 (a) (i))

Items removed from driver's view prior to test ()

Manufactures engine and body covers fitted restricting inspection of components

Nearside Front Inner Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))

Nearside Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Inner Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))

Offside Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Parking brake grabbing inboard shoes

Rear axle corroding at fixing points

Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear cross member nearside and offside (6.1.1 (c) (i))

Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Nearside Front Lower Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) DANGEROUS

Offside Front Nail in tyre ()

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b))

Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Headlamp not working on dipped beam n/s ans o/s (4.1.1 (a) (ii))

Headlamp not working on main beam n/s and o/s (4.1.1 (a) (ii))

Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Nearside Rear Position lamp not working (4.2.1 (a) (ii))

Nearside Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Nail in tyre ()

Offside Rear quarter panel corroded

Nearside Windscreen washer provides insufficient washer liquid (8.2.3)

Offside Rear fog lamp missing (1.3.2a)

Offside Rear quarter panel corroded

Offside Headlamp deteriorated but light output not reduced (1.7.5a)

Front registration plate delaminated (6.3.1d)

Nearside Front Seat belt anchorage prescribed area is excessively corroded backing sill (5.2.6)

Nearside Front Seat belt anchorage prescribed area is excessively corroded outer sill (5.2.6)

Nearside Front Subframe mounting prescribed area is excessively corroded backing sill (2.4.A.3)

Nearside Rear Seat belt anchorage prescribed area is excessively corroded backing sill (5.2.6)

Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill (2.4.A.3)

Offside Front Seat belt anchorage prescribed area is excessively corroded backing sill (5.2.6)

Offside Headlamp excessively deteriorated so that the light output is severely reduced (1.7.5a)

Offside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill (2.4.A.3)

Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Rear Rear fog lamp emits a light other than red (1.3.2e)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Windscreen washer provides insufficient washer liquid (8.2.3)

heavy surface corrosion rear arches

Front Brake pad(s) wearing thin (3.5.1g)

front pads low

only drivers seat fitted at time of test so unable to check seat belts for other seats