MOT Status
ExpiredMileage
145,217 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Central Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b))
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))
Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Nearside Rear Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i))
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Nearside Rear Upper Suspension arm pin or bush excessively worn outer (5.3.4 (a) (i))
Offside Rear Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i))
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Offside Rear Upper Suspension arm pin or bush excessively worn outer (5.3.4 (a) (i))
Offside Rear fog lamp adversely affected by the operation of another lamp comes on with sidelight (4.5.4 (b))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Aux belt guard loose
Fuel Pipe/s corroded ()
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive underbody (5.3.6 (a) (i))
Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement trailing arm (5.3.4 (a) (i))
Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Offside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive underbody (5.3.6 (a) (i))
Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))
Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement trailing arm (5.3.4 (a) (i))
Offside Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))
Oil leak, but not excessive (8.4.1 (a) (i))
Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))
Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Offside Front Suspension arm ball joint has slight play just about passable (5.3.4 (a) (i))
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive inner arch (5.3.6 (a) (i))
Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))
corrosion in front floors and rear inner sills
fuel pipes corroding
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement perished (5.3.4 (a) (i))
Offside Front Anti-roll bar ball joint has slight play (5.3.4 (a) (i))
Offside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))
Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement perished (5.3.4 (a) (i))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill (5.3.6 (a) (i))
Offside Rear Upper Suspension arm pin or bush worn but not resulting in excessive movement slight play (5.3.4 (a) (i))
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))
Rear fog lamp not working (4.5.1 (a) (ii))
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement perished (5.3.4 (a) (i))
Offside Front Anti-roll bar ball joint has slight play (5.3.4 (a) (i))
Offside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))
Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement perished (5.3.4 (a) (i))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill (5.3.6 (a) (i))
Offside Rear Upper Suspension arm pin or bush worn but not resulting in excessive movement slight play (5.3.4 (a) (i))
Front Brakes imbalanced across an axle (3.7.B.5b)
Offside rear parking brake recording little or no effort (3.7.B.6a)
Parking brake: efficiency below requirements (3.7.B.7)
Nearside Rear Suspension arm rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)
Offside Rear Suspension arm rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)
PARKING BRAKE EFFICIENCY ONLY JUST MET
Parking brake lever has little reserve travel (3.1.6b)
Nearside Rear Suspension arm rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)
Offside Rear Suspension arm rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)
PARKING BRAKE EFFICIENCY ONLY JUST MET
Parking brake lever has little reserve travel (3.1.6b)
Rear fog lamp tell tale not working (1.3.1b)
Brake pipe slightly corroded FRONT TO REAR (3.6.B.2c)
Suspension component mounting prescribed area is corroded but not considered excessive BOTH FRONT FLOORS (2.4.A.3)
Offside Rear Suspension component mounting prescribed area is excessively corroded CHASSIS (2.4.A.3)
Brake pipe slightly corroded FRONT TO REAR (3.6.B.2c)
Suspension component mounting prescribed area is corroded but not considered excessive BOTH FRONT FLOORS (2.4.A.3)
Nearside Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a)
Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)
Brake pipe slightly corroded (3.6.B.2c)
Offside Seat belt stitching slightly frayed (5.2.2b)
Brake pipe slightly corroded (3.6.B.2c)
Offside Front Seat belt stitching slightly frayed (5.2.2b)
Nearside Registration plate lamp not working (1.1.C.1d)
Nearside Steering rack gaiter split (2.2.D.2d)
Nearside front brake binding (3.7.B.1)
Brake pipe slightly corroded (3.6.B.2c)
Offside Front Seat belt stitching slightly frayed (5.2.2b)
Nail in offside front tyre
Nearside Rear wheel bearing has slight play (2.6.2)
Nearside Registration plate lamp not working (1.1.C.1d)
Offside Rear wheel bearing has slight play (2.6.2)
Nail in offside front tyre
Nearside Rear wheel bearing has slight play (2.6.2)
Offside Rear wheel bearing has slight play (2.6.2)
Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)
Offside rear parking brake recording little or no effort (3.7.B.6a)
Parking brake lever has no reserve travel (3.1.6b)
Parking brake: efficiency below requirements (3.7.B.7) DANGEROUS
Brake pipe slightly corroded (3.6.B.2c)
Nearside Rear Upper Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)
Offside Rear Upper Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)
Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)
Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)
Exhaust emissions hydrocarbon content after 2nd fast idle excessive (7.3.D.3)
Exhaust emits dense blue smoke at idle (7.3.A.2b)
Exhaust emits excessive dense blue smoke during acceleration (7.3.A.2c)
Nearside Rear brake disc in such a condition that it is seriously weakened (3.5.1i)
Offside Front Headlamp not working on dipped beam (1.7.5a)
Offside Front Tyre tread depth below requirements of 1.0mm (4.1.E.2b)
Offside Rear Wheel insecure (4.2.A.1c)
Offside Rear brake disc in such a condition that it is seriously weakened (3.5.1i)
Parking brake: efficiency below requirements (3.7.B.7)
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension arm has slight play in a pin/bush (2.4.G.2)
Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)
Front Brake pad(s) less than 1.5 mm thick (3.5.1g)
Offside Headlamp not working on dipped beam (1.7.5a)
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Rear Suspension arm has slight play in a pin/bush (2.4.G.2)
How Reliable is the Mitsubishi Fto?
Based on 55,254 MOT tests across 5,410 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
P704 YGF is a 1996 Mitsubishi Fto in Maroon with a 1,990cc petrol engine. This vehicle has been through 25 MOT tests with a personal pass rate of 52%.
Across all 1996 Mitsubishi Fto models, the average MOT pass rate is 65.0% with a typical mileage of 96,396 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Mitsubishi Fto fails its MOT is suspension component mounting prescribed area is excessively corroded, accounting for 4,056 recorded failures. If you're considering buying P704 YGF, it's worth having these areas checked by a mechanic before committing.
The Mitsubishi Fto typically stays on UK roads for around 32 years. At 30 years old, this Mitsubishi Fto is approaching the upper end of the typical lifespan for this model.
Frequently Asked Questions
How do I check the history of P704 YGF?
You can check the full history of P704 YGF by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was P704 YGF registered?
P704 YGF is a 1996 Mitsubishi Fto, first registered on 31 December 1996.
Is P704 YGF safe to buy?
The MOT history for P704 YGF shows 25 tests with a 52% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does P704 YGF have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on P704 YGF. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.