MOT Status
ValidMileage
119,415 miAbove average mileage for this year
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Rear Brake hose slightly deteriorated (1.1.12 (b) (ii))
Offside Rear Brake hose slightly deteriorated (1.1.12 (b) (ii))
Emissions unable to be completed (8.2.1.2 (d))
Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Rear floor corroded
Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Oil leak, but not excessive (8.4.1 (a) (i))
general corrosion of suspension componants
Front Tyre slightly damaged/cracking or perishing both (5.2.3 (d) (ii))
Front subframe corroded
Nearside Front Lower Anti-roll bar linkage pin or bush worn but not resulting in excessive movement bush (5.3.4 (a) (i))
Nearside Front Suspension arm corroded but not seriously weakened upper and lower (5.3.3 (b) (i))
Nearside Rear Brake pipe corroded, covered in grease or other material nearside to offside (1.1.11 (c))
Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Offside Front Suspension arm corroded but not seriously weakened upper and lower (5.3.3 (b) (i))
Offside Rear Nail in tyre
Oil leak, but not excessive (8.4.1 (a) (i))
Nearside Headlamp aim too high (4.1.2 (a))
Nearside Rear Shock absorbers has a serious fluid leak (5.3.2 (b))
Offside Headlamp aim too low (4.1.2 (a))
Front Tyre slightly damaged/cracking or perishing both (5.2.3 (d) (ii))
Front subframe corroded
Nearside Front Lower Anti-roll bar linkage pin or bush worn but not resulting in excessive movement bush (5.3.4 (a) (i))
Nearside Front Suspension arm corroded but not seriously weakened upper and lower (5.3.3 (b) (i))
Nearside Rear Brake pipe corroded, covered in grease or other material nearside to offside (1.1.11 (c))
Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Offside Front Suspension arm corroded but not seriously weakened upper and lower (5.3.3 (b) (i))
Offside Rear Nail in tyre
Oil leak, but not excessive (8.4.1 (a) (i))
Nearside Front Shock absorbers has a serious fluid leak (5.3.2 (b))
Body has slight corrosion (6.1.B.2)
Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)
Central Brake pipe slightly corroded (3.6.B.2c)
Central Rear Brake pipe slightly corroded (3.6.B.2c)
Front Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Front Ball joint dust cover deteriorated, but preventing the ingress of dirt all (2.2.C.1c)
Front Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)
Front Inner Brake pipe slightly corroded both sides (3.6.B.2c)
Front Lower Seat belt anchorage prescribed area is corroded but not considered excessive both sides (5.2.6)
Front Shock absorber has slight corrosion to the casing both sides (2.7.2a)
Front Sub-frame corroded but not seriously weakened (2.4.G.1)
Front Suspension arm corroded but not seriously weakened all (2.4.G.1)
Front Suspension arm rubber bush deteriorated but not resulting in excessive movement all (2.4.G.2)
Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Front registration plate deteriorated but not likely to be misread (6.3.1d)
Rear Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Rear Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)
Rear Shock absorber has slight corrosion to the casing both sides (2.7.2a)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Rear Suspension arm corroded but not seriously weakened all (2.4.G.1)
Rear Suspension arm rubber bush deteriorated but not resulting in excessive movement all (2.4.G.2)
Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Vehicle structure has slight corrosion (6.1.A.1)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
all metal brake pipes covered in sealer
all rear driveshaft boots deteriorated
front exhaust sections deteriorated and rear exhaust fouling rear bumper
fuel pipes corroded
minor oil leaks
under trays fitted
Nearside Front Lower Seat belt anchorage prescribed area is inadequately repaired (5.2.6)
Body has slight corrosion (6.1.B.2)
Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)
Central Brake pipe slightly corroded (3.6.B.2c)
Central Rear Brake pipe slightly corroded (3.6.B.2c)
Front Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Front Ball joint dust cover deteriorated, but preventing the ingress of dirt all (2.2.C.1c)
Front Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)
Front Inner Brake pipe slightly corroded both sides (3.6.B.2c)
Front Lower Seat belt anchorage prescribed area is corroded but not considered excessive both sides (5.2.6)
Front Shock absorber has slight corrosion to the casing both sides (2.7.2a)
Front Sub-frame corroded but not seriously weakened (2.4.G.1)
Front Suspension arm corroded but not seriously weakened all (2.4.G.1)
Front Suspension arm rubber bush deteriorated but not resulting in excessive movement all (2.4.G.2)
Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Front registration plate deteriorated but not likely to be misread (6.3.1d)
Rear Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Rear Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)
Rear Shock absorber has slight corrosion to the casing both sides (2.7.2a)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Rear Suspension arm corroded but not seriously weakened all (2.4.G.1)
Rear Suspension arm rubber bush deteriorated but not resulting in excessive movement all (2.4.G.2)
Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Vehicle structure has slight corrosion (6.1.A.1)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
all metal brake pipes covered in sealer
all rear driveshaft boots deteriorated
front exhaust sections deteriorated and rear exhaust fouling rear bumper
fuel pipes corroded
minor oil leaks
under trays fitted
Body has slight corrosion (6.1.B.2)
Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)
Centre Brake pipe slightly corroded (3.6.B.2c)
Centre Rear Brake pipe slightly corroded (3.6.B.2c)
Front Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Front Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)
Front Inner Brake pipe slightly corroded both sides (3.6.B.2c)
Front Lower Seat belt anchorage prescribed area is corroded but not considered excessive both sides (5.2.6)
Front Shock absorber has slight corrosion to the casing both sides (2.7.2a)
Front Sub-frame corroded but not seriously weakened (2.4.G.1)
Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Front registration plate deteriorated but not likely to be misread (6.3.1d)
Nearside Front Suspension arm corroded but not seriously weakened upper and lower (2.4.G.1)
Nearside Rear Suspension arm corroded but not seriously weakened upper and lower (2.4.G.1)
Offside Front Suspension arm corroded but not seriously weakened upper and lower (2.4.G.1)
Offside Rear Suspension arm corroded but not seriously weakened upper and lower (2.4.G.1)
Rear Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Rear Brake hose has slight corrosion to ferrules both sides (3.6.B.4e)
Rear Shock absorber has slight corrosion to the casing both sides (2.7.2a)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Vehicle structure has slight corrosion (6.1.A.1)
all metal brake pipes covered in sealer
all rear driveshaft boots deteriorated
front exhaust sections deteriorated
fuel pipes corroded
minor oil leaks
rear exhaust fouling rear bumper
Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)
Centre Brake pipe slightly corroded (3.6.B.2c)
Front Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Front Brake hose has slight corrosion to ferrules (3.6.B.4e)
Front Lower Ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)
Front Sub-frame corroded but not seriously weakened (2.4.G.1)
Front Suspension arm corroded but not seriously weakened (2.4.G.1)
Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Front Upper Ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)
Front registration plate delaminated but not likely to be misread (6.3.1d)
Fuel pipe/s corroded
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Rear Road wheel slightly damaged (4.2.A.1a)
Rear Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Rear Brake hose has slight corrosion to ferrules (3.6.B.4e)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Track rod end ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)
Vehicle structure has slight corrosion (6.1.A.1)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
exhaust system deteriorated at time of test
Front Brake pad(s) less than 1.5 mm thick (3.5.1g)
Front brake disc in such a condition that it is seriously weakened (3.5.1i)
Nearside rear parking brake recording little or no effort (3.7.B.6a)
Rear brake disc in such a condition that it is seriously weakened (3.5.1i)
Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)
Centre Brake pipe slightly corroded (3.6.B.2c)
Front Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Front Brake hose has slight corrosion to ferrules (3.6.B.4e)
Front Lower Ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)
Front Sub-frame corroded but not seriously weakened (2.4.G.1)
Front Suspension arm corroded but not seriously weakened (2.4.G.1)
Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Front Upper Ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)
Front registration plate delaminated but not likely to be misread (6.3.1d)
Fuel pipe/s corroded
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Rear Road wheel slightly damaged (4.2.A.1a)
Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)
Rear Anti-roll bar corroded but not seriously weakened (2.4.G.1)
Rear Brake hose has slight corrosion to ferrules (3.6.B.4e)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Track rod end ball joint dust cover deteriorated, but preventing the ingress of dirt (2.2.C.1c)
Vehicle structure has slight corrosion (6.1.A.1)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
exhaust system deteriorated at time of test
Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)
Front Sub-frame corroded but not seriously weakened (2.4.G.1)
Front Suspension arm corroded but not seriously weakened (2.4.G.1)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Vehicle structure has slight corrosion (6.1.A.1)
exhaust system deteriorated at time of test
Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)
Front Sub-frame corroded but not seriously weakened (2.4.G.1)
Front Suspension arm corroded but not seriously weakened (2.4.G.1)
Offside Front Brake pipe slightly corroded (3.6.B.2c)
Offside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Vehicle structure has slight corrosion (6.1.A.1)
exhaust system deteriorated at time of test
Parking brake: efficiency below requirements (3.7.B.7)
Nearside Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Nearside rear brake recording little or no effort (3.7.B.5a)
Nearside rear parking brake recording little or no effort (3.7.B.6a)
Nearside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Rear Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Brake pipe slightly corroded (3.6.B.2c)
Front Brake master cylinder/servo mounting prescribed area is corroded but not considered excessive (3.6.C.3)
Front Sub-frame corroded but not seriously weakened (2.4.G.1)
Nearside Front Lower Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Front Lower Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Rear Sub-frame corroded but not seriously weakened (2.4.G.1)
Steering component mounting prescribed area is corroded but not considered excessive (2.2.C.1h)
Suspension arm corroded but not seriously weakened (2.4.G.1)
Nearside Sub-frame corroded but not seriously weakened (2.4.G.1)
Nearside Suspension arm corroded but not seriously weakened (2.4.G.1)
Nearside Suspension arm corroded but not seriously weakened (2.4.G.1)
Offside Sub-frame corroded but not seriously weakened (2.4.G.1)
Offside Rear coil spring fractured (2.4.C.1a)
Rear Exhaust has part of the system excessively deteriorated (7.1.1a)
Nearside Front Headlamp aim too high (1.8)
Front Suspension arm corroded but not seriously weakened (2.4.G.1)
Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Nearside Outer Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Offside Outer Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Front Suspension arm corroded but not seriously weakened (2.4.G.1)
Rear Suspension arm corroded but not seriously weakened (2.4.G.1)
Brake pipe slightly corroded (3.6.B.2c)
Exhaust has part of the system slightly deteriorated (7.1.1a)
Nearside Front brake disc slightly scored (3.5.1h)
Nearside Rear brake disc slightly scored (3.5.1h)
Offside Front brake disc slightly scored (3.5.1h)
Offside Rear brake disc slightly scored (3.5.1h)
Rear Brake pad(s) wearing thin (3.5.1g)
Vehicle structure has slight corrosion (6.1.B.2)
Vehicle structure has slight corrosion (6.1.B.2)
fuel tank showing signs of corrosion
Seat belt anchorage prescribed area is corroded but not considered excessive (5.2.6)
Nearside Front Brake pad(s) wearing thin (3.5.1g)
Offside Front Brake pad(s) wearing thin (3.5.1g)
How Reliable is the Mazda MX-5?
Based on 2,502,760 MOT tests across 160,823 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
P880 ACY is a 1996 Mazda MX-5 in Red with a 1,840cc petrol engine. This vehicle has been through 31 MOT tests with a personal pass rate of 67.7%.
Across all 1996 Mazda MX-5 models, the average MOT pass rate is 69.8% with a typical mileage of 86,097 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Mazda MX-5 fails its MOT is seat belt anchorage prescribed area is excessively corroded, accounting for 44,475 recorded failures. If you're considering buying P880 ACY, it's worth having these areas checked by a mechanic before committing.
The Mazda MX-5 typically stays on UK roads for around 36 years. At 30 years old, this Mazda MX-5 is approaching the upper end of the typical lifespan for this model.
Frequently Asked Questions
How do I check the history of P880 ACY?
You can check the full history of P880 ACY by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was P880 ACY registered?
P880 ACY is a 1996 Mazda MX-5, first registered on 2 August 1996.
Is P880 ACY safe to buy?
The MOT history for P880 ACY shows 31 tests with a 67.7% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does P880 ACY have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on P880 ACY. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.