1997 Rover 111

General underside corrosion

Rear panel corroded and holed

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Windscreen washer not working both (3.5 (a))

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

General underside corrosion

Rear panel corroded and holed

Items removed from driver's view prior to test ()

Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive subframe mounting. (5.3.6 (a) (i))

cover sills fitted.

rear lower valance corroded..!!

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sub frame mounting.. (5.3.6 (a) (i))

Items removed from driver's view prior to test ()

Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive subframe mounting. (5.3.6 (a) (i))

cover sills fitted.

rear lower valance corroded..!!

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Front Direction indicator incorrect colour (4.4.3 (a))

Offside Front Direction indicator incorrect colour (4.4.3 (a))

Nearside Front Tyre tread depth below requirements of 1.6mm inner edge (5.2.3 (e)) DANGEROUS

Nearside Rear Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Offside Front Tyre has ply or cords exposed inner edge (5.2.3 (d) (ii)) DANGEROUS

Offside Front Tyre tread depth below requirements of 1.6mm inner edge (5.2.3 (e)) DANGEROUS

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to the legal limit inner edge just legal (4.1.E.1)

Front Suspension has inadequate clearance with the bump stop (2.4.A.1a)

Nearside Front Suspension arm corroded and seriously weakened (2.4.G.1)

Nearside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Nearside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside rear brake binding (3.7.B.1)

Exhaust has a minor leak of exhaust gases (7.1.2)

fuel filler neck/pipe corroded

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Brakes imbalanced across an axle (3.7.B.5b)

Nearside rear brake recording little or no effort (3.7.B.5a)

Registration plate lamp not working (1.1.C.1d)

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Nearside Headlamp aim too low (1.8)

Nearside Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Front Suspension has inadequate clearance with the bump stop (2.4.A.1a)

Nearside Headlamp aim too low (1.8)

Offside Headlamp aim too low (1.8)

Offside rear brake recording little or no effort (3.7.B.5a)

rear brake application uneven (3.7.B.2)

rear brakes release unevenly (3.7.B.4)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Nearside Front Headlamp aim too low (1.8)

Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Brake pipe excessively corroded (3.6.B.2c)

Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Body has a sharp edge caused by corrosion (6.1.C.1)

Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Track rod end ball joint has excessive play (2.2.B.1f)

Offside Rear Rear position lamp(s) adversely affected by the operation of another lamp (1.1.A.3f)

Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)