2012 Mercedes-benz Cls

Nearside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Tyre worn close to legal limit/worn on edge Inner edge (5.2.3 (e))

Offside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Coil spring fractured or broken (5.3.1 (b) (i))

Nearside Rear Tyre worn close to legal limit/worn on edge wearing on inner edge (5.2.3 (e))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Oil leak, but not excessive (8.4.1 (a) (i))

wiper blades slight worn

Nearside Rear Tyre worn close to legal limit/worn on edge wearing on inner edge (5.2.3 (e))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Oil leak, but not excessive (8.4.1 (a) (i))

Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))

wiper blades slight worn

Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Wheel bearing has slight play (5.1.3 (a) (i))

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Direction indicator not working (4.4.1 (a) (ii))

Offside Front Headlamp insecure (4.1.1 (c))

Rear Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Nearside Front Wheel bearing has slight play (5.1.3 (a) (i))

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Wheel bearing has slight play (5.1.3 (a) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material of main (1.1.11 (c))

Offside Front Outer Tyre slightly damaged/cracking or perishing edge (5.2.3 (d) (ii))

Offside Rear hand brake has only just met requirements may need adjustment or repair

Rear Brake pipe corroded, covered in grease or other material of main (1.1.11 (c))

Nearside Front Outer Tyre has a tear, caused by separation or partial failure of its structure edge (5.2.3 (d) (ii)) DANGEROUS

Nearside Front Inner Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Wheel bearing has slight play (5.1.3 (a) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material of main (1.1.11 (c))

Offside Front Outer Tyre slightly damaged/cracking or perishing edge (5.2.3 (d) (ii))

Offside Rear hand brake has only just met requirements may need adjustment or repair

Rear Brake pipe corroded, covered in grease or other material of main (1.1.11 (c))

Nearside Front Brake pipe corroded, covered in grease or other material (end) (1.1.11 (c))

Nearside Rear Brake pipe corroded, covered in grease or other material (end) (1.1.11 (c))

Offside Front Brake pipe corroded, covered in grease or other material (end) (1.1.11 (c))

Offside Rear Brake pipe corroded, covered in grease or other material (end) (1.1.11 (c))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Rear Rear fog lamp not working (4.5.1 (a) (ii))

Nearside Front Brake pipe corroded, covered in grease or other material (end) (1.1.11 (c))

Nearside Rear Brake pipe corroded, covered in grease or other material (end) (1.1.11 (c))

Offside Front Brake pipe corroded, covered in grease or other material (end) (1.1.11 (c))

Offside Rear Brake pipe corroded, covered in grease or other material (end) (1.1.11 (c))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front coil spring broken (2.4.C.1a)

Nearside Rear coil spring broken (2.4.C.1a)

Offside Rear coil spring broken (2.4.C.1a)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)