2005 Fiat Ducato

Nearside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sills (6.1.1 (c) (i))

Offside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sills (6.1.1 (c) (i))

Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i))

Nearside Rear Tyre has a bulge, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Offside Rear Tyre has a bulge, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Nearside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sills (6.1.1 (c) (i))

Offside Inner Integral body structure is corroded but structural rigidity is not significantly reduced sills (6.1.1 (c) (i))

Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength bottom of inner wing (5.3.6 (a) (i))

Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength bottom of rear panel to mount (5.3.6 (a) (i))

Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii))

Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Front Coil spring corroded (5.3.1 (b) (i))

chassis has surface corrosion

exhaust outer skin peeling

Exhaust system insecure rubbers mounts split (6.1.2 (a))

Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Front Coil spring corroded (5.3.1 (b) (i))

chassis has surface corrosion

exhaust outer skin peeling

Front Brakes imbalanced across an axle 40% IMBALANCE OS LOW EFFORT (1.2.1 (b) (i))

Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced HOLED AND CORRODED INNER SILL CENTRE SECTION (6.1.1 (c) (i))

Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced CHASSIS LED NEAR FRONT CROSS MEMBER (6.1.1 (c) (i))

Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced SMALL HOLE AT FRONT OF SUSPENSION TURRET (6.1.1 (c) (i))

Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL HOLED AND CORRODED CENTRE SECTION (6.1.1 (c) (i))

Rear Tyre worn close to legal limit/worn on edge Both wearing on inner edges (5.2.3 (e))

Emissions not tested Exhaust blow (8.2.2.2 (e))

Exhaust has a major leak of exhaust gases Centre pipe rusted (6.1.2 (a))

Headlamp aim too low Both (4.1.2 (a))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill/chasis leg (5.3.6 (a) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear of inner arch (5.3.6 (a) (i))

Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear of inner arch (5.3.6 (a) (i))

Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a))

Rear Tyre worn close to legal limit/worn on edge Both wearing on inner edges (5.2.3 (e))

Offside Rear Suspension spring mounting prescribed area is excessively corroded DROP SILL (2.4.A.3)

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Headlamp aim too low (1.8)

Offside Rear Direction indicator incorrect colour (1.4.A.2f)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

Windscreen wiper does not clear the windscreen effectively Both (8.2.2)

engine mounting deteriorated resulting in excessive movement Rear gearbox steady bar (6.1.D.1a)

rear brake recording little or no effort Offside lower, load sensor may need adjusting (3.7.B.5a)

Slight wiper mark on o/s windscreen

Nearside front brake binding (3.7.B.1)

Fuel system component leaking (7.2.3)

Fuel system component leaking (7.2.3)