2006 Lexus RX400H

Front Registration plate insecure (0.1 (a))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Offside Rear Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) DANGEROUS

Nearside Rear Nail in tyre ()

Nearside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Rear Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Central Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement inner bush (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill / rear jacking point area (5.3.6 (a) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement inner bush (5.3.4 (a) (i))

Offside Front Subframe mounting prescribed area is corroded but not considered excessive inner sill / outrigger and jacking point area. (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill / rear jacking point area. (5.3.6 (a) (i))

Rear Anti-roll bar attachment bracket/mounting corroded but its strength is not seriously reduced both sides. (5.3.3 (b) (i))

Rear Brake hose has slight corrosion to ferrule all and both sides. (1.1.12 (f) (i))

Rear Brake pipe corroded, covered in grease or other material both sides in various spots. (1.1.11 (c))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Sub-frame pin or bush worn but not resulting in excessive movement all rear mounting bushes perished. (5.3.4 (a) (i))

Rear subframe mounting brackets corroded.

Central Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Front Headlamp aim projected beam image is obviously incorrect BOTH SIDES due to the opaque lenses. (4.1.2 (c))

Front Headlamp aim unable to be tested both sides due to the opaque and distorted projected beam image. (4.1.2 (b))

Offside Front Position lamp not working side light. (4.2.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Registration plate lamp inoperative in the case of a single lamp or all lamps both sides. (4.7.1 (b) (ii))

Central Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement inner bush (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill / rear jacking point area (5.3.6 (a) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement inner bush (5.3.4 (a) (i))

Offside Front Subframe mounting prescribed area is corroded but not considered excessive inner sill / outrigger and jacking point area. (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill / rear jacking point area. (5.3.6 (a) (i))

Rear Anti-roll bar attachment bracket/mounting corroded but its strength is not seriously reduced both sides. (5.3.3 (b) (i))

Rear Brake hose has slight corrosion to ferrule all and both sides. (1.1.12 (f) (i))

Rear Brake pipe corroded, covered in grease or other material both sides in various spots. (1.1.11 (c))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Sub-frame pin or bush worn but not resulting in excessive movement all rear mounting bushes perished. (5.3.4 (a) (i))

Rear subframe mounting brackets corroded.

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive suspension arm / inner sill and rear jacking point damaged and distorted. (5.3.6 (a) (i))

Offside Front Subframe mounting prescribed area is corroded but not considered excessive outrigger / inner sill and jacking point (5.3.6 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement inner bushes slightly perished (5.3.4 (a) (i))

Offside Front brake disc back blade dust cover missing.

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive suspension arm/ inner sill and rear jacking point damaged and distorted. (5.3.6 (a) (i))

Rear Brake hose has slight corrosion to ferrule all rear and both sides. (1.1.12 (f) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Sub-frame pin or bush worn but not resulting in excessive movement mounting bushes slightly perished. (5.3.4 (a) (i))

both rear brake discs dust covers corroded.

engine covers and undertrays fitted obscuring testable items from view of the test.

Rear both sides rear breaks binding slightly evidently shown on the overheated blued discs.

Front Registration plate inscription illegible (0.1 (b))

Nearside Front Headlamp aim too low (4.1.2 (a))

Nearside Front Position lamp not working side light. (4.2.1 (a) (ii))

Offside Front Headlamp aim too low (4.1.2 (a))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Front Headlamp lens slightly defective both sides slightly opaque. (4.1.1 (b) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive suspension arm / inner sill and rear jacking point damaged and distorted. (5.3.6 (a) (i))

Offside Front Subframe mounting prescribed area is corroded but not considered excessive outrigger / inner sill and jacking point (5.3.6 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement inner bushes slightly perished (5.3.4 (a) (i))

Offside Front brake disc back blade dust cover missing.

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive suspension arm/ inner sill and rear jacking point damaged and distorted. (5.3.6 (a) (i))

Rear Brake hose has slight corrosion to ferrule all rear and both sides. (1.1.12 (f) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Sub-frame pin or bush worn but not resulting in excessive movement mounting bushes slightly perished. (5.3.4 (a) (i))

both rear brake discs dust covers corroded.

engine covers and undertrays fitted obscuring testable items from view of the test.

Rear both sides rear breaks binding slightly evidently shown on the overheated blued discs.

Front Brake hose has slight corrosion to ferrule both sides. (1.1.12 (f) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Front both front brake discs back plates corroded.

Nearside Rear Suspension arm corroded but not seriously weakened both track rod arms and trailing arm corroded. (5.3.3 (b) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill rear jacking point (5.3.6 (a) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing outer wall. (5.2.3 (d) (ii))

Offside Front Subframe mounting prescribed area is corroded but not considered excessive outrigger to subframe mount. (5.3.6 (a) (i))

Offside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive inner sill / rear jacking point. (5.3.6 (a) (i))

Offside Rear Suspension arm corroded but not seriously weakened both trailing arm and offside rear track rod arms corroded (5.3.3 (b) (i))

Rear Brake hose has slight corrosion to ferrule both sides. (1.1.12 (f) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Subframe mounting prescribed area is corroded but not considered excessive including subframe mounting brackets. (5.3.6 (a) (i))

Rear both rear brake discs back plates / covers corroded and missing.

Fuel Pipe/s corroded including fuel tank swan neck section and returns. ()

Central Exhaust has a major leak of exhaust gases (6.1.2 (a))

Offside Rear Tyre not fitted in accordance with side wall instructions wrong direction of rotation. (5.2.3 (i))

Front Brake hose has slight corrosion to ferrule both sides. (1.1.12 (f) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Front both front brake discs back plates corroded.

Nearside Rear Suspension arm corroded but not seriously weakened both track rod arms and trailing arm corroded. (5.3.3 (b) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill rear jacking point (5.3.6 (a) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing outer wall. (5.2.3 (d) (ii))

Offside Front Subframe mounting prescribed area is corroded but not considered excessive outrigger to subframe mount. (5.3.6 (a) (i))

Offside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive inner sill / rear jacking point. (5.3.6 (a) (i))

Offside Rear Suspension arm corroded but not seriously weakened both trailing arm and offside rear track rod arms corroded (5.3.3 (b) (i))

Rear Brake hose has slight corrosion to ferrule both sides. (1.1.12 (f) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Subframe mounting prescribed area is corroded but not considered excessive including subframe mounting brackets. (5.3.6 (a) (i))

Rear both rear brake discs back plates / covers corroded and missing.

Fuel Pipe/s corroded including fuel tank swan neck section and returns. ()

Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Lower Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Rear Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brake disc significantly and obviously worn (1.1.14 (a) (i))

Rear Brakes imbalanced across an axle (1.2.1 (b) (i))

Rear Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Lower Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Rear Nail in tyre ()

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Front Brake damaged, but the braking system is not adversely affected both brake discs back plates corroded (1.1.21 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened both sides (1.1.14 (a) (ii))

Front Brake pipe corroded, covered in grease or other material both sides (1.1.11 (c))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Front Suspension arm corroded but not seriously weakened all and both sides slightly corroded (5.3.3 (b) (i))

Nearside Rear Brake damaged, but the braking system is not adversely affected brake disc back plate corroded (1.1.21 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill (5.3.6 (a) (i))

Offside Rear Brake damaged, but the braking system is not adversely affected brake disc back plate corroded away and missing. (1.1.21 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill (5.3.6 (a) (i))

Rear Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened both sides (1.1.14 (a) (ii))

Rear Brake hose has slight corrosion to ferrule both sides (1.1.12 (f) (i))

Rear Brake pipe corroded, covered in grease or other material both sides (1.1.11 (c))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Suspension arm corroded but not seriously weakened all and both sides slightly corroded (5.3.3 (b) (i))

fuel filler neck pipe corroded

Nearside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

offside rear brake disc back plate missing

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Engine covers fitted obscuring some components in the engine bay

O/S/F suspension arm back bush slightly deteriorated

Under-trays fitted obscuring some underside components

Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Front Tyre worn close to the legal limit (4.1.E.1)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

front brake discs corroded...

Front Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Nearside rear brake grabbing slightly (3.7.A.5b)

Offside rear brake grabbing slightly (3.7.A.5b)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)