1998 Mazda Bongo

Front Vehicle structure is deformed but structural rigidity is not significantly reduced Both front sill seams at jacking areas (6.1.1 (a) (i))

Hand brake close to max travel

Nearside Rear Oil leak, but not excessive Some evidence of oil on engine (8.4.1 (a) (i))

Offside Front Small hole in corner of roof

Offside Rear Tyre worn close to legal limit/worn on edge Tread depth very close to 1.6mm (5.2.3 (e))

Rear Exhaust has a minor leak of exhaust gases At flexi pipe area (6.1.2 (a))

Rear Trailer electrical socket insecure (4.10 (a) (i))

Steering rack has slight free play detected at steering wheel (2.3 (a) (i))

Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Nearside Front Coil spring mounting insecure Spring not mounted correctly in top mount (5.3.1 (a) (i))

Nearside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Front Vehicle structure is deformed but structural rigidity is not significantly reduced Both front sill seams at jacking areas (6.1.1 (a) (i))

Hand brake close to max travel

Nearside Rear Oil leak, but not excessive Some evidence of oil on engine (8.4.1 (a) (i))

Offside Front Small hole in corner of roof

Offside Rear Tyre worn close to legal limit/worn on edge Tread depth very close to 1.6mm (5.2.3 (e))

Rear Exhaust has a minor leak of exhaust gases At flexi pipe area (6.1.2 (a))

Rear Trailer electrical socket insecure (4.10 (a) (i))

Steering rack has slight free play detected at steering wheel (2.3 (a) (i))

Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

underbody welded covered in underseal

Headlamp aim unable to be tested (4.1.2 (b))

Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) DANGEROUS

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

underbody welded covered in underseal

Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced CROSS MEMBER (6.1.1 (c) (i))

Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL (6.1.1 (c) (i))

Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL (6.1.1 (c) (i))

Offside Rear Position lamp not working (4.2.1 (a) (ii))

Offside Front Brake Grabbing

Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) DANGEROUS

Offside Front Brake Grabbing

Nearside Front Upper Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Offside Front Upper Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Rear Exhaust has part of the system slightly deteriorated (7.1.1a)

both front tyres wearing edges of tread

Exhaust has a major leak of exhaust gases (7.1.2)

Exhaust has a part missing (7.1.1a)

Offside Stop lamp not working (1.2.1b)

both front tyres wearing edges of tread

Offside Rear Anti-roll bar attachment bracket/mounting insecure (2.4.G.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)