2006 Mazda Bongo

Coolant leak ()

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Inner Brake pad(s) wearing thin VERY LOW - REQUIRES ATTENTION ASAP (1.1.13 (a) (ii))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced various locations on vehicle (6.1.1 (c) (i))

Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Shock absorbers has a serious fluid leak (5.3.2 (b))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill - chalked (5.3.6 (a) (i))

Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis - by top coil spring mounting - chalked (6.1.1 (c) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis - by top coil spring mounting - chalked (6.1.1 (c) (i))

Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))

Front Brake disc worn, pitted or scored, but not seriously weakened inner face (1.1.14 (a) (ii))

Nearside Front Inner Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement d bush (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Vehicle structure is corroded but structural rigidity is not significantly reduced various locations (6.1.1 (c) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Front Inner Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Lower Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security under rad chassis (6.2.2 (d) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Nail in tyre ()

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Coil spring corroded (5.3.1 (b) (i))

Rear Inner Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security wings (6.2.2 (d) (i))

Vehicle structure is repaired but structural rigidity is not significantly reduced vehicle platted and welded heavy undershield (6.1.1 (d) (i))

Front Windscreen washer not working (3.5 (a))

Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Front Brake hose excessively twisted not fixed (1.1.12 (b) (ii))

Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))

Nearside Rear Inner Tyre has a tear, caused by separation or partial failure of its structure and outer (5.2.3 (d) (ii)) DANGEROUS

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Front Inner Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Lower Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security under rad chassis (6.2.2 (d) (i))

Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Nail in tyre ()

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Coil spring corroded (5.3.1 (b) (i))

Rear Inner Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security wings (6.2.2 (d) (i))

Vehicle structure is repaired but structural rigidity is not significantly reduced vehicle platted and welded heavy undershield (6.1.1 (d) (i))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Coil spring corroded (5.3.1 (b) (i))

Offside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i))

Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i))

Subframe mounting prescribed area excessively corroded significantly reducing structural strength front crossmember (5.3.6 (a) (i))

Rear Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Coil spring corroded (5.3.1 (b) (i))

Offside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Front Inner Integral body structure is corroded but structural rigidity is not significantly reduced Wheel arch (6.1.1 (c) (i))

Nearside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Rear Tyre slightly damaged/cracking or perishing Both (5.2.3 (d) (ii))

Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i))

Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i))

Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i))

Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i))

Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Front Inner Integral body structure is corroded but structural rigidity is not significantly reduced Wheel arch (6.1.1 (c) (i))

Nearside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Rear Tyre slightly damaged/cracking or perishing Both (5.2.3 (d) (ii))

Brake pipe corroded, covered in grease or other material All (1.1.11 (c))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Unable to check rear seat belts as seats stowed away

Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i))

Nearside Headlamp light intensity severely reduced (4.1.4 (a))

Nearside Headlamp not working on main beam (4.1.1 (a) (ii))

Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wheel arch (6.1.1 (c) (i))

Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i))

Brake pipe corroded, covered in grease or other material All (1.1.11 (c))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Unable to check rear seat belts as seats stowed away

Nearside Front Inner Wheel arch corroded/holed

Nearside Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Flexible brake hose partially insecure

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Exhaust has a major leak of exhaust gases Intermediate pipe (6.1.2 (a))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Front Inner Wheel arch corroded/holed

Nearside Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Flexible brake hose partially insecure

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Track rod end ball joint dust cover damaged or deteriorated, but preventing the ingress of dirt (2.1.3 (g) (i))

Offside Rear fog lamp not working (4.5.1 (a) (ii))

Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i))

Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i))

Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Rear Anti-roll bar linkage damaged and seriously weakened (5.3.3 (b) (i))

Rear fog lamp missing (4.5.1 (a) (ii))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Nail in tyre ()

Offside Rear Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Rear Shock absorber has slight corrosion to the casing (2.7.2a)

Offside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Rear Shock absorber has slight corrosion to the casing (2.7.2a)

Nearside Registration plate lamp not working (1.1.C.1d)

Nearside Stop lamp not working (1.2.1b)

Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Front Suspension component mounting prescribed area is excessively corroded wishbone (2.4.A.3)

Rear fog lamp not working (1.3.2b)

Nearside Front Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Rear Shock absorber has slight corrosion to the casing (2.7.2a)

Offside Outer Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Rear Shock absorber has slight corrosion to the casing (2.7.2a)

Battery insecure (1.9.1)

Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f)

Nearside Front Inner Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)

Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch (2.4.A.3)

Nearside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Rear fog lamp insecure (1.3.2a)

Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f)

Nearside Front Suspension component mounting prescribed area is excessively corroded inner arches (2.4.A.3)

Nearside Front Suspension component mounting prescribed area is excessively corroded outrigger (2.4.A.3)

Nearside Rear Body has a sharp edge caused by corrosion arches (6.1.C.1)

Nearside Rear Suspension component mounting prescribed area is excessively corroded inner arches (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is excessively corroded sill top (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded chassi (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded inner arches (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded outer sills (2.4.A.3)

Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting inner back panel (6.6.6)

surface corrosion all around underbody areas

corrosion to rear brake discs

o/s/r bump stop missing

rear shock absorber covers corroded

Luggage not allowing full inspection of both rear adult seatbelts

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside front tyre worn on outer edge

Offside rear bumper support corroded

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Temporary fuel cap fitted

Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f)

Nearside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Headlamp not working on dipped beam (1.7.5a)

Offside Front Headlamp not working on main beam (1.7.5a)

Rear Stop lamp adversely affected by the operation of another lamp (1.2.1f)

Luggage not allowing full inspection of both rear adult seatbelts

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside front tyre worn on outer edge

Offside rear bumper support corroded

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Temporary fuel cap fitted

corrosion to rear discs and pads wearing low

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

corrosion to rear discs and pads wearing low

offside front tyre cracking

outer sills corroded

rear brake discs pitted

rear shockabsorber covers corroded

Direction indicators adversely affected by the operation of another lamp (1.4.A.2h)

Fuel system component leaking (7.2.3)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Rear Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance (1.3.2d)

Rear Stop lamp adversely affected by the operation of another lamp (1.2.1f)

Offside Front Macpherson strut has slight movement at the upper attachment (2.5.A.1c)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

both sills corroded

o/s/f tyre cracking

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement (7.2.4b)

Nearside Rear Anti-roll bar attachment bracket/mounting fractured (2.4.G.1)

Rear fog lamp switch faulty (1.3.1a)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Temporary fuel cap fitted

Nearside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Rear fog lamp missing (1.3.2a)

Temporary fuel cap fitted

both front wheels binding

Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear fog lamp not working (1.3.2b)

Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement (2.4.G.2)

Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement (2.4.G.2)

Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Brake pad(s) less than 1.5 mm thick (3.5.1g) DANGEROUS

Service brake: efficiency below requirements (3.7.C.1a) DANGEROUS