1997 Rover 111

Nearside Rear Service brake requirements only just met. It would appear that the braking system requires adjustment or repair (1.2.1 (c))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill (5.3.6 (a) (i))

Offside front floor / jacking point slightly corroded

Underside of vehicle & brake pipes coated in underseal

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Nearside Rear Suspension component leaking schrader valve (5.3.5 (c))

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Nearside Rear Service brake requirements only just met. It would appear that the braking system requires adjustment or repair (1.2.1 (c))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill (5.3.6 (a) (i))

Offside front floor / jacking point slightly corroded

Stop lamp(s) all not working (4.3.1 (a) (iii)) DANGEROUS

Central Brake pipe excessively corroded both (1.1.11 (c))

Exhaust carbon monoxide content at idle exceeds manufacturer's specified limits (8.2.1.2 (b))

Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacing point (6.1.1 (c) (i))

Nearside Inner Floor excessively deteriorated floor/sill holed and corrooded (6.2.4 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Offside Rear Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) DANGEROUS

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Subframe mounting prescribed area damaged but not considered excessive (5.3.6 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Upper Integral body structure is corroded but structural rigidity is not significantly reduced cross member running underside of boot/floorpan corroded (6.1.1 (c) (i))

Rear metal vent fuel pipe corroded

existing welding repairs satisfactory

nearside and offside plastic sill covers fitted

Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Slight corrosion to rear arches

Vehicle heavily undersealed

Windscreen damaged but not adversely affecting driver's view small chip (3.2 (a) (i))

Offside Front Lower Suspension arm ball joint has slight play (5.3.4 (a) (i))

Rear Exhaust has a minor leak of exhaust gases slight exhaust blow at rear joint (6.1.2 (a))

Surface corrosion to underbody

Nearside Front Inner Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Front Lower Ball joint has slight play (2.2.B.1f)

Near side front bottom ball joint getting worn

Some corrosion off side front subframe/floor mounting point

Windscreen chipped

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Near side front bottom ball joint getting worn

Some corrosion off side front subframe/floor mounting point

Windscreen chipped

Both rear tyres have uneven wear to inside edge

Handbrake cables rubbing on rear subframe

Exhaust front flex pipe getting corroded.

Off side front tyre scrubing inner edge.

Small hole near side front subframe.

Front Suspension has inadequate clearance with the bump stop (2.4.A.1a)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

Parking brake: efficiency below requirements (3.7.B.7)