1998 Kawasaki ZX-7R

Rear Suspension pin, bush or joint worn but not resulting in excessive movement Swing arm bush. (5.3.4 (a) (i))

Front All position lamps not working Side light. (4.2.1 (a))

Front Motorcycle structure joining/attachment plate or fastening insecure (6.1.1 (b) (i))

Front All direction indicators flashing more than 120 times a minute (4.4.4 (a))

Front Tire over 5 years old.

Rear All direction indicators flashing more than 120 times a minute (4.4.4 (a))

Rear Suspension pin, bush or joint worn but not resulting in excessive movement Swing arm bush. (5.3.4 (a) (i))

Rear Tire over 5 years old.

Exhaust slightly deteriorated exhaust system rusting but not blowing (7.1.1a)

Rear Brake disc(s) slightly scored (3.2.A1l)

Steering headbearing has slight free play very slight play (2.2.2)

Wheel alignment slightly misaligned. (2.5.1)

nearside riders footrest rubber missing

Horn control defective button fault, horn does not operate every time button is pressed (1.7.2a)

Nearside Front Brake disc(s) cracked (3.2.A1g)

Offside Front Brake disc(s) cracked (3.2.A1g)

Rear Brake pedal has inadequate reserve travel brake feels soft,did not lock rollers on brake test,and pedal has too much travel. (3.1.3b)

Roller brake test The less effective brake control does not achieve an efficiency of 25%. (3.3.A2b)

Exhaust slightly deteriorated exhaust system rusting but not blowing (7.1.1a)

Rear Brake disc(s) slightly scored (3.2.A1l)

Steering headbearing has slight free play very slight play (2.2.2)

Wheel alignment slightly misaligned. (2.5.1)

front brake lever operation slightly rough,pivot needs greasing . not affecting brake operation

nearside riders footrest rubber missing

Offside Front Brake disc(s) cracked (3.2.A1g)

Front Brake disc(s) slightly scored (3.2.A1l)

Nearside Front Brake disc(s) slightly pitted (3.2.A1l)

Rear Brake disc(s) slightly pitted (3.2.A1l)

Steering headbearing has slight free play (2.2.2)

Wheel alignment slightly misaligned. (2.5.1)

front bake lever does not pull up smoothly has rough feel to it

front near side foot rest has rubber missing but still secure and usable

Front Roller brake test indicates slight fluctuation of brake effort (3.3.A1d)

Offside Front shock absorber has light misting of stanchion (2.3.3)

Drive chain excessively tight (6.2.1d)

Front Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))

Throttle operating incorrectly (6.2.1f)

Front Roller brake test indicates slight fluctuation of brake effort (3.3.A1d)

Offside Front shock absorber has light misting of stanchion (2.3.3)

Rear Roller brake test Higher brake efficiency normally obtainable. (3.3.A2a)

rear brake binding slightly, not enough to fail

Chain guard missing

Exhaust slightly deteriorated (7.1.1a)

Front Tyre worn close to the legal limit (4.1.3(ii))

Nearside Front Brake disc(s) slightly pitted (3.2.A1l)

Offside Front Brake disc(s) slightly pitted (3.2.A1l)

Rear Drive chain slightly loose (6.2.1d)

Rear suspension bearing has slight free play (2.4.A2a(i))

Chain guard missing

Exhaust slightly deteriorated (7.1.1a)

Rear wheel bearings have slight free play (2.4.A.2c)

both front and rear tyre pressures were low and have been re-inflated

front and rear brake lever pivots could do with lubricating. both slightly stiff but not enough to warrant failure

Chain guard missing

Front Roller brake test indicates a slightly grabbing brake (3.3.A1b)

Front wheel spindle securing nut locking device insecure (2.3.5a)

Rear Drive chain slightly tight (6.2.1d)

Rear wheel has a loose wheel nut(s) (4.2.3a)

Chain guard missing

Front Roller brake test indicates a slightly grabbing brake (3.3.A1b)

Rear Drive chain slightly tight (6.2.1d)

Front Floor brake test indicates a binding brake (3.3.C2c)

Front Roller brake test indicates a binding brake (3.3.A1a)

Front Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))

Locking device(s) not correctly fitted which may make the motor bicycle dangerous to ride (6.2.1h)

Rear Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))

Chain guard missing

drive chain very dry and requires lubrication

only one of the two tail light bulbs works

Front Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))