2009 Ford Ka

Central Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Oil leak, but not excessive (8.4.1 (a) (i))

Central Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Registration plate lamp inoperative in the case of a single lamp or all lamps both (4.7.1 (b) (ii))

Front Lower Oil leak, but not excessive engine oil (8.4.1 (a) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Brake servo defective or ineffective (1.1.10 (a) (i))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Nearside Rear Braking system leaking oil leaking from inside drums (1.1.3 (d))

Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Windscreen wiper does not clear the windscreen effectively offside wiper wrong size,left un-wiped area on offside and middle (3.4 (b) (ii))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Rear Exhaust has a major leak of exhaust gases Rear pipe seal leak (6.1.2 (a))

Service brake efficiency below requirements (1.2.2 (a) (i))

Front Brakes imbalanced across an axle by more than 50% Axle 1 (1.2.1 (b) (ii)) DANGEROUS

Front Lower Oil leak, but not excessive engine oil (8.4.1 (a) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Front Brake pad(s) wearing thin both front os/ns (1.1.13 (a) (ii))

Nearside Front Upper Shock absorbers has a slightly worn bush top mount (5.3.2 (c))

Nearside Rear Brake pipe corroded, covered in grease or other material behind hub (1.1.11 (c))

Rear Vehicle structure is corroded but structural rigidity is not significantly reduced suspension components including axle general corrosion (6.1.1 (c) (i))

Front Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Brake cable insecure (1.1.15 (c))

Offside Rear Brake cable damaged (1.1.15 (a))

Front Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Shock absorbers has light misting of oil (5.3.2 (b))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Exhaust has a minor leak of exhaust gases rear box (6.1.2 (a))

Nearside Front Fluid leak, but not excessive gearbox (8.4.1 (a) (i))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i))

Nearside Rear Parking brake inoperative on one side fluid leak at brake drum (1.4.1 (a))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Nearside Front Fluid leak, but not excessive gearbox (8.4.1 (a) (i))

Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

exhaust system corroded

Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Nearside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b))

Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

exhaust system corroded

near side rear tyre 2mm low on edges 175/65/14

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

near side rear tyre 2mm low on edges 175/65/14

front pads low close to limit

rear exhaust corroded slight blow

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Headlamp aim too low (1.8)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)