2003 Fiat Doblo

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Shock absorbers has a serious fluid leak (5.3.2 (b))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Shock absorber has a light misting of oil (2.7.3)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Leaf spring has excessive wear in a shackle pin and/or bush (2.4.B.2)

Offside passenger door cannot be opened from outside the vehicle (6.2.B.1c)

Service brake: efficiency below requirements (3.7.B.7)

Nearside Rear Shock absorber has a light misting of oil (2.7.3)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Front Exhaust has a major leak of exhaust gases flexi pipe holed (7.1.2)

Power steering pump drive system defective belt split (2.3.6)

Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Rear Shock absorber has a light misting of oil (2.7.3)

Offside Front Front constant velocity joint gaiter damaged, but preventing the ingress of dirt (2.5.C.1a)

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Nearside Headlamp aim too high (1.8)

Offside Headlamp aim too high (1.8)

n/s rear bump stop missing

n/s rear bump stop missing

Front Anti-roll bar corroded but not seriously weakened (2.4.G.1)

Nearside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Front coil spring corroded (2.4.C.1b)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front coil spring corroded (2.4.C.1b)

both rear suspension bump stops are worn.

exhaust system corroded.

nsf tyre worn on edges (raised tread)

osf brake pipe is slightly corroded.

Nearside Registration plate lamp not working (1.1.C.1d)

Parking brake lever, pawl mechanism pivots or their associated mountings are insecure (3.1.4b)

Front Anti-roll bar corroded but not seriously weakened (2.4.G.1)

Nearside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Front coil spring corroded (2.4.C.1b)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front coil spring corroded (2.4.C.1b)

both rear suspension bump stops are worn.

exhaust system corroded.

nsf tyre worn on edges (raised tread)

osf brake pipe is slightly corroded.

front pads low discs worn

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Rear Seat belt damaged but webbing not significantly weakened (5.2.2a)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Exhaust emits an excessive level of metered smoke for a turbo charged engine (7.4.B.3b)

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Offside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Rear Seat belt damaged but webbing not significantly weakened (5.2.2a)

Parking brake lever, pawl mechanism pivot(s) retaining device insecure (3.1.4b)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Rear Exhaust has part of the system slightly deteriorated (7.1.1a)

Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Front Brake pad(s) wearing thin (3.5.1g)

Rear tyres worn to 2mm

Headlamp aim too low (1.8)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Headlamp not in good working order adversely affecting beam image (1.2.4a)

Front Brake pad(s) wearing thin (3.5.1g)

Rear tyres worn to 2mm

Nearside Front Suspension arm has excessive play in a pin/bush (2.4.G.2)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)