1998 Honda CBR1100XX

Rear Motorcycle structure is corroded but structural rigidity is not significantly reduced sub frame (6.1.1 (c) (i))

Drive chain sprocket worn, but not excessively (6.1.7 (c) (i))

Drive chain worn but not considered excessive (6.1.7 (c) (i))

Offside Front Shock absorber has a light misting of oil (5.3.2 (b))

Rear Road spring corroded (5.3.1 (b) (i))

Rear brake pads corroded

Front Brake excessively binding (1.2.1 (f))

Rear Suspension component attachment bracket/mounting corroded and seriously weakened suspension linkage under swingarm (5.3.3 (b) (i))

Front Tyre has a tear caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Rear Tyre has a tear caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Drive chain sprocket worn, but not excessively (6.1.7 (c) (i))

Drive chain worn but not considered excessive (6.1.7 (c) (i))

Offside Front Shock absorber has a light misting of oil (5.3.2 (b))

Rear Road spring corroded (5.3.1 (b) (i))

Rear brake pads corroded

Front Brake binding but not excessively (1.2.1 (f))

Nearside Exhaust has a minor leak of exhaust gases Joint (6.1.2 (a))

Rear Brake indicates slight fluctuation of brake effort (1.2.1 (e))

Front Brake binding but not excessively (1.2.1 (f))

Front Stop lamp switch with a delay in operation Control (4.3.2 (a) (ii))

Nearside Exhaust has a minor leak of exhaust gases Joint (6.1.2 (a))

Rear Brake indicates slight fluctuation of brake effort (1.2.1 (e))

Front Tyre is unsuitable Not fitted in accordance with sidewall instruction (5.2.3 (a))

Front Stop lamp does not illuminate immediately a brake applies (1.3.1a)

Front Tyre worn close to the legal limit (4.1.3(ii))

Front suspension assembly slightly corroded. fork stanchions (2.3.1)

Front Brake pad(s) close to minimum limit (3.2.A1f(i))

Front suspension has slight corrosion (2.3.8)

Rear Brake pad(s) close to minimum limit (3.2.A1f(i))

Registration plate with character(s) which are not the correct height (6.3.4a)

Front Brake pad(s) close to minimum limit (3.2.A1f(i))

Front suspension has slight corrosion (2.3.8)

Rear Brake pad(s) close to minimum limit (3.2.A1f(i))

Exhaust noisy (7.1.2)

Rear Brake pad(s) close to minimum limit (3.2.A1f(i))

Rear suspension bearing has slight free play (2.4.A2a(i))

Stop lamp does not illuminate immediately a brake applies (1.3.1a)

Wheel alignment incorrect which adversely affects the handling (2.5.1)

Exhaust noisy (7.1.2)

Rear Brake pad(s) close to minimum limit (3.2.A1f(i))

Rear suspension bearing has slight free play (2.4.A2a(i))

Drive chain slightly loose (6.2.1d)

Exhaust is leaking but is not excessively noisey (7.1.1b)

Rear Tyre worn close to the legal limit (4.1.3(ii))

Front Brake pad(s) (sintered type) less than 1.0mm thick (3.2A1f(ii))

Front Tyre worn close to the legal limit (4.1.3(ii))

Exhaust noisy (7.1.2)

Front Brake pad(s) close to minimum limit (3.2A1f(ii))

Front Tyre worn close to the legal limit (4.1.3(ii))

Front Brake pad(s) close to minimum limit (3.2.A1f(i))

Front Roller brake test indicates a slightly grabbing brake (3.3.A1b)

Nearside Brake fluid reservoir fluid level low (3.2.B1d)

Rear Exhaust noisy (7.1.2)

Front Headlamp aim too high (hotspot centre above the horizontal 0% line) (1.6.1)

Offside Rear Brake pad(s) less than 1.5 mm thick (3.2.A1f(i))

Front Roller brake test indicates a slightly grabbing brake (3.3.A1b)

Rear Exhaust noisy (7.1.2)