2004 Mercedes-benz Slk

Brake pipe corroded, covered in grease or other material Front to rear (1.1.11 (c))

Exhaust system corroded and leak at back box

Front Coil spring corroded (5.3.1 (b) (i))

Front Shock absorbers has slight external damage to the casing Corroded (5.3.2 (b))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Tyre worn close to legal limit/worn on edge All 4 low and perished (5.2.3 (e))

Front Shock absorbers has slight external damage to the casing X 2 RUSTY (5.3.2 (b))

Front Brake disc significantly and obviously worn (1.1.14 (a) (i))

Headlamp aim too high X 2 (4.1.2 (a))

Oil leaking excessively from transmission (8.4.1 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Front Brake hose has slight corrosion to ferrule X 2 (1.1.12 (f) (i))

Front Shock absorbers has slight external damage to the casing X 2 RUSTY (5.3.2 (b))

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Rear Brake hose has slight corrosion to ferrule X 2 (1.1.12 (f) (i))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Nearside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Front Lower Suspension arm ball joint excessively worn rear arm (5.3.4 (a) (i))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Nearside Front Brake pipe excessively corroded (1.1.11 (c))

Offside Front Brake pipe excessively corroded (1.1.11 (c))

Rear Service brake excessively binding both (1.2.1 (f))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Brake drum back plate insecure back plates corroded (1.1.14 (d))

Headlamps matched pair are incorrectly positioned main beam and head lights both iluminate when activated (4.1.4 (a))

Nearside Rear Rear fog lamp not working (4.5.1 (a) (ii))

Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Rear Registration plate lamp does not illuminate simultaneously with the position lamps (4.7.2 (a))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Central Rear Upper Stop lamp not working (1.2.1b)

Nearside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt alloy arm (2.2.C.1c)

Nearside Rear rear parking (secondary) brake grabbing severely (3.7.B.6b)

Nearside rear brake binding (3.7.B.1)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords tyre been damaged before possible from snap spring tyre is showing cord from where it was rubbing (4.1.D.1a)

Rear Brake pad(s) wearing thin (3.5.1g)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Front coil spring broken (2.4.C.1a)

Offside Front Shock absorber has a serious fluid leak (2.7.3)

Offside Registration plate lamp not working (1.1.C.1d)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Front Suspension arm has excessive play in a ball joint (2.4.G.2)

Front registration plate character(s) incorrectly spaced (6.3.4a)

Offside Registration plate lamp not working (1.1.C.1d)

Rear registration plate character(s) incorrectly spaced (6.3.4a)

Nearside Front Headlamp not working on dipped beam (1.7.5a)