2005 Fiat Idea

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b))

Nearside Front Suspension arm pin or bush excessively worn Rear bush of wishbone bonding failed, bush out of casing. (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch structure holed/corrded within 30cm of upper shock absorber mount. (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill holed/corroded within 30cm of axle mounting. (5.3.6 (a) (i))

Nearside Rear Upper Shock absorbers has an excessively worn bush (5.3.2 (c))

Offside Direction indicator incorrect colour indicator repeater. (4.4.3 (a))

Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength outer sill holed/corroded within 30cm of rear mounting. (5.3.6 (a) (i))

Offside Front Suspension arm pin or bush excessively worn Rear bush of wishbone bonding failed, bush out of casing. (5.3.4 (a) (i))

Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill holed/corroded within 30cm of axle mounting. (5.3.6 (a) (i))

Rear Exhaust has a major leak of exhaust gases Silncer holed. (6.1.2 (a))

Nearside Front Subframe mounting prescribed area is corroded but not considered excessive outer sill corroded within 30cm of rear mounting. (5.3.6 (a) (i))

Nearside Front Windscreen wiper blade defective rubber torn (3.4 (b) (i))

Offside Front Strut top mounting worn.

Oil leak, but not excessive engine (8.4.1 (a) (i))

Oil leak, but not excessive gearbox (8.4.1 (a) (i))

Rear Direction indicator slightly discoloured both (4.4.3 (a))

Rear both tyres badly perished and splitting although no ply/cord visable.

Rear exhaust shield insecure.

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Offside Prop shaft joint constant velocity boot no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Tyre tread depth below requirements of 1.6mm nearside and offside front (5.2.3 (e)) DANGEROUS

Headlamp aim beam image obviously incorrect (1.8.A.1b)

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Rear Direction indicators obviously incorrectly positioned (1.4.A.2b)

Offside Rear Direction indicators slightly discoloured (1.4.A.2f)

cooling fan inop!

o/s/f tyre worn on inner edge

rear exhaust silencer ( outer cover split )

Offside Rear Direction indicators slightly discoloured (1.4.A.2f)

cooling fan inop!

o/s/f tyre worn on inner edge

rear exhaust silencer ( outer cover split )

Nearside Front Lower Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Front Lower Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Offside Front Side repeater slightly discoloured (1.4.A.2f)

Offside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Rear Upper Shock absorber has a slightly worn bush (2.7.4)

Exhaust system not adequately supported (7.1.1)

Nearside Front Headlamp aim too high (1.8)

Nearside Side repeater incorrect colour (1.4.A.2f)

Offside Front Headlamp aim too high (1.8)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)