2005 Subaru Outback

Nearside Front Anti-roll bar linkage damaged and seriously weakened (5.3.3 (b) (i))

Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i))

Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i))

Registration plate lamp does not illuminate simultaneously with the position lamps Both (4.7.2 (a))

Offside Rear Tyre has ply or cords exposed (5.2.3 (d) (ii)) DANGEROUS

All rear suspension components are very corroded.

Nearside Front Shock absorbers has slight external damage to the casing Body very rusty. (5.3.2 (b))

Nearside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Shock absorbers has slight external damage to the casing Body very rusty. (5.3.2 (b))

Offside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Nail in tyre ()

Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))

Nearside Rear Nail in tyre ()

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Stop lamp not working (1.2.1b)

Offside Front position lamp(s) not working (1.1.A.3b)

Parking brake: efficiency below requirements (3.7.D.4)

Supplementary Restraint System warning lamp indicates a fault (5.4.2)

Exhaust corroded

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

rear exhaust mount deteriorated

tyres wearing inner and outer edges

Nearside Headlamp not working on dipped beam (1.7.5a)

Nearside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Exhaust corroded

Offside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

rear exhaust mount deteriorated

tyres wearing inner and outer edges

Engine covers fitted obscuring some components in the engine bay

Under-trays fitted obscuring some underside components

Offside Outer Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Offside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

both rear tyre's wearing on inner and outer edge's.

front reg plate deteriorated.

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.D.2c)

Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)