2012 Ford Mondeo

in my option this vehicle suffers from advanced corr

Rear Sub-frame pin or bush excessively worn (5.3.4 (a) (i))

in my option this vehicle suffers from advanced corr

Front both tyres worn on outer edges

Exhaust emissions exceed manufacturer's specified limit (8.2.2.2 (a))

Nearside Rear Brake cable damaged cable frayed (1.1.15 (a))

Nearside Rear Road wheel fixing missing (5.2.1 (a) (i))

Front both tyres worn on outer edges

Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f))

Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Parking brake inoperative on one side (1.4.1 (a))

Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Track rod end ball joint has excessive play (2.1.3 (b) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Parking brake lever has excessive movement indicating incorrect adjustment offside cable broken (1.1.6 (c))

Brake hydraulic reservoir close to minimum mark (1.1.10 (d) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Track rod end ball joint has slight play (2.1.3 (b) (i))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

possible inlet pipe leak above undertray

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement Trailing arm. Also starting to split (5.3.4 (a) (i))

Nearside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement Trailing arm. Also starting to split (5.3.4 (a) (i))

Offside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Nearside Headlamp aim so that beam "kick up" is not visible on the screen (4.1.2 (a))

Nearside Headlamp insecure (4.1.1 (c))

Nearside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i))

Offside Headlamp aim so that beam "kick up" is not visible on the screen (4.1.2 (a))

Offside Headlamp insecure (4.1.1 (c))

Offside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i))

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Electrical wiring insulation slightly damaged or deteriorated Exhaust sensor wire (4.11 (c) (i))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement Trailing arm. Also starting to split (5.3.4 (a) (i))

Nearside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement Trailing arm. Also starting to split (5.3.4 (a) (i))

Offside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Central Upper Stop lamp not working (1.2.1b)

Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Offside Registration plate lamp not working (1.1.C.1d)

Nearside Front Headlamp aim beam image obviously incorrect (1.8.A.1b)

Offside Front Headlamp aim beam image obviously incorrect (1.8.A.1b)