2012 Toyota Hilux

Central Front Steering component mounting prescribed area is corroded but not considered excessive Mounting cross member (2.1.2 (e) (i))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement D bush (5.3.4 (a) (i))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Lower Seat belt anchorage prescribed area is corroded but not considered excessive Inner sills (7.1.1 (a) (i))

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive Front and rear leaf spring mounting areas (5.3.6 (a) (i))

Nearside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive Shock absorber mounting (5.3.6 (a) (i))

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement D bush (5.3.4 (a) (i))

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Lower Seat belt anchorage prescribed area is corroded but not considered excessive Inner sills (7.1.1 (a) (i))

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive Front and rear leaf spring mounting areas (5.3.6 (a) (i))

Offside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive Shock absorber mounting (5.3.6 (a) (i))

Brake hydraulic reservoir cap missing (1.1.10 (e))

Engine MIL inoperative or indicates a malfunction (8.2.2.2 (g))

Horn not working (7.7 (a))

Offside Headlamp aim too low (4.1.2 (a))

Offside Lower Headlamp insecure (4.1.1 (c))

Offside Rear fog lamp not working (4.5.1 (a) (ii))

Rear Prop shaft joint excessively worn Centre joint (6.1.7 (c) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Offside Front Inner Brake lining(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Central Front Steering component mounting prescribed area is corroded but not considered excessive Mounting cross member (2.1.2 (e) (i))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement D bush (5.3.4 (a) (i))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Lower Seat belt anchorage prescribed area is corroded but not considered excessive Inner sills (7.1.1 (a) (i))

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive Front and rear leaf spring mounting areas (5.3.6 (a) (i))

Nearside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive Shock absorber mounting (5.3.6 (a) (i))

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement D bush (5.3.4 (a) (i))

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Offside Lower Seat belt anchorage prescribed area is corroded but not considered excessive Inner sills (7.1.1 (a) (i))

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive Front and rear leaf spring mounting areas (5.3.6 (a) (i))

Offside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive Shock absorber mounting (5.3.6 (a) (i))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Front Service brake imbalance requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Lower Anti-roll bar ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Front Service brake binding but not excessively (1.2.1 (f))

Nearside Rear Service brake fluctuating, but not excessively (1.2.1 (e))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Service brake imbalance requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Front Service brake imbalance requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Lower Anti-roll bar ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Front Service brake binding but not excessively (1.2.1 (f))

Nearside Rear Service brake fluctuating, but not excessively (1.2.1 (e))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Stop lamp(s) not working (4.3.1 (a) (ii))

Rear Service brake imbalance requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Rear Child Seat fitted not allowing full inspection of adult belt

Central Brake pipe excessively corroded Both rear sections of centre brake pipes (3.6.B.2c)

Nearside Rear Brake pipe excessively corroded load valve to hose (3.6.B.2c)

Offside Registration plate lamp not working (1.1.C.1d)

Nearside Rear Child Seat fitted not allowing full inspection of adult belt

metal brake pipe corroding offside centre chassis to load sensor valve