2010 Peugeot 107

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b))

Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive both sides (5.3.6 (a) (i))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b))

Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sills (6.1.1 (c) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive both sides (5.3.6 (a) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Brake pipe corroded, covered in grease or other material all pipes greased in places (1.1.11 (c))

Exhaust has a minor leak of exhaust gases also has perished hangers (6.1.2 (a))

Front Coil spring corroded both (5.3.1 (b) (i))

Headlamp lens slightly defective both (4.1.1 (b) (i))

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Rear Coil spring corroded both also rubber seats not correctly located (5.3.1 (b) (i))

Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Tyre slightly damaged/cracking or perishing all (5.2.3 (d) (ii))

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

exhaust down pipe corroded

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b))

Rear Exhaust has a major leak of exhaust gases at joint (6.1.2 (a))

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Coil spring corroded (5.3.1 (b) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

exhaust down pipe corroded

Offside Front Tyre worn close to the legal limit (4.1.E.1)

nearside rear tyre cracked slightly & close to legal limit

Centre Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

nearside rear tyre cracked slightly & close to legal limit

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)