1981 Bedford Van

Oil leak

general underbody corrosion for age of vehicle

Bonnet retaining device ineffective (8.4.2)

Centre Exhaust has a major leak of exhaust gases (7.1.2)

Exhaust system not adequately supported (7.1.1)

Front Brake pipe excessively corroded (3.6.B.2c)

Headlamp switch insecure (1.7.1)

Nearside Front Shock absorber insecure (2.7.2b)

Nearside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Nearside Headlamp not working on dipped beam (1.7.5a)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Headlamp not working on dipped beam (1.7.5a)

Offside Rear wheel bearing rough when rotated (2.6.1)

Offside front brake binding (3.7.B.1)

front brake application uneven (3.7.B.2)

rear brake application uneven (3.7.B.2)

Front Upper Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Oil leak

Prop-shaft universal joint worn

both rear tyres perishing on sidewalls

Centre Exhaust has a minor leak of exhaust gases (7.1.2)

Coolant leak

Nearside Front Body has slight corrosion (6.1.B.2)

Nearside Front Suspension arm worn but not seriously weakened (2.4.G.1)

Offside Front Suspension arm worn but not seriously weakened (2.4.G.1)

Oil leak

Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.C.1b)

Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.C.1a)

brake pedal soft

full exhaust system is coroaded

Coolant leak

Oil leak

Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Brakes imbalanced across an axle (3.7.B.5b) DANGEROUS

Vehicle structure has slight corrosion (6.1.A.1)

oil leak

advise brake inspection.....

Fuel cap/sealing device does not fasten securely by positive means (7.2.4b)

Headlamp switch faulty (1.7.1)

Windscreen washer provides insufficient washer liquid (8.2.3)

rear brake application uneven (3.7.B.2)

Front front brake application uneven (3.7.B.2) DANGEROUS

front brake pipes corroding...

general under & upper body corrosion....

long hand brake lever travel....

oil leaks.....

Brake pedal creeps down while the pedal is held under pressure (3.3.B.1a)

Brake performance not tested (3.7.A.1)

Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement (7.2.4b)

Headlamp aim not tested (1.8.A.1c)

Headlamp not working on dipped beam (1.7.5a)

Headlamp not working on main beam (1.7.5a)

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Front Shock absorber has an excessively worn bush (2.7.4)

Nearside Inner Front Suspension component mounting prescribed area is inadequately repaired (2.4.A.3)

Nearside Inner Rear Subframe mounting prescribed area is inadequately repaired (2.4.A.3)

Nearside Rear Leaf spring has excessive side play at eye (anchor) (2.4.B.4)

Nearside Rear Lower Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Registration plate lamp shows direct white light to the rear (1.1.C.1f)

Offside Front Lower Seat belt anchorage prescribed area is inadequately repaired (5.2.6)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front brake drum contaminated by oil (3.5.1h)

Offside Inner Front Subframe mounting prescribed area is excessively corroded (2.4.A.3)

Offside Inner Front Subframe mounting prescribed area is inadequately repaired (2.4.A.3)

Offside Rear Braking system leaking (3.6.A.1)

Offside Rear Lower Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Upper Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

Windscreen washer provides insufficient washer liquid (8.2.3)

Brake pedal spongy (3.3.B.1b) DANGEROUS

Brake pipe excessively corroded (3.6.B.2c) DANGEROUS

Nearside Front Brake hose excessively deteriorated (3.6.B.4d) DANGEROUS

Nearside Passenger's seat cannot be secured in the upright position. (6.2.A.2) DANGEROUS

Offside Rear brake drum contaminated by oil (3.5.1h) DANGEROUS

Brake hose has slight corrosion to ferrules (3.6.B.4e)

Coolant leak

Exhaust emits blue smoke during acceleration (7.3.A.2c)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Fuel pipe/s corroded

Hydraulic brake cylinder corroded but not excessively weakened (3.6.A.2b)

Lower Steering column universal joint has slight play (2.1.5)

Nearside Front wheel bearing has slight play (2.5.A.3c)

Offside Front Shock absorber has a slightly worn bush (2.7.4)

Rear Shock absorber has slight corrosion to the casing (2.7.2a)

Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Steering system has slight free play detected at steering wheel (2.2.A.1b)

Suspension joint offside upper dust cover split/missing

front suspension arm and rear leaf spring bushes deteriorated

front tie bar bushes deteriorated/worn

heavy corrosion forming on underside components,surfaces and prescribed areas

nearside tyres badly deteriorated /cracking/marginal in places

Oil leak

Propshaft component defective

VEHICLE STRUCTURE HAS ADVANCED CORROSION AND IS INTEGRALLY WEAK

engine cover missing

nearside rear tyre punctured? flat

Brakes imbalanced across an axle (3.7.B.5b)

Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement (7.2.4b)

Headlamp switch faulty (1.7.1)

Nearside Front Shock absorber insecure (2.7.2b)

Nearside Windscreen washer provides insufficient washer liquid (8.2.3)

Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Registration plate lamp not illuminating the registration plate (1.1.C.1e)

front brake application uneven (3.7.B.2)

Nearside rear brake recording little or no effort (3.7.B.5a) DANGEROUS

Offside rear brake recording little or no effort (3.7.B.5a) DANGEROUS

Service brake: efficiency below requirements (3.7.B.7) DANGEROUS

front brake pipes corroding....

general under body & upper body corrosion.....

oil leaks....

Brake pedal spongy (3.3.B.1b)

Brake pipe excessively corroded (3.6.B.2c)

Braking system leaking (3.6.A.1)

Fuel cap/sealing device does not fasten securely by positive means (7.2.4b)

Hazard warning lamps not flashing in phase, with ignition on (1.4.B.1f)

Hazard warning switch faulty (1.4.B.1d)

Nearside Front Lower Shock absorber has an excessively worn bush (2.7.4)

Nearside Headlamp not working on dipped beam (1.7.5a)

Nearside Headlamp not working on main beam (1.7.5a)

Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Rear Braking system leaking (3.6.A.1)

Offside Rear rear brake application uneven (3.7.B.2)

Offside Rear rear parking brake recording little or no effort (3.7.B.6a)

Offside Seat belt anchorage prescribed area is inadequately repaired (5.2.6)

Windscreen washer provides insufficient washer liquid (8.2.3)

rear brake application uneven (3.7.B.2)

Offside Front Lower Shock absorber has a slightly worn bush (2.7.4)

major oil leak from engine

prop shaft universal joints very worn

Brake pedal spongy (3.3.B.1b)

Brake pipe excessively corroded (3.6.B.2c)

Direction indicators flashing more than 120 times a minute (1.4.A.2g)

Exhaust emissions hydrocarbon content excessive (7.3.B.1b)

Front Brake pipe excessively corroded (3.6.B.2c)

Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement (7.2.4b)

Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f)

Hazard warning lamps not flashing in phase, with ignition on (1.4.B.1f)

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Front Direction indicators not working (1.4.A.2c)

Nearside Front Headlamp not working on main beam (1.7.5a)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside rear brake recording little or no effort (3.7.B.5a)

Offside Front Direction indicators not working (1.4.A.2c)

Offside Front Front position lamp(s) not working (1.1.A.3b)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Front Upper Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Braking system leaking (3.6.A.1)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear fog lamp emits a light other than red (1.3.2e)

Offside Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance (1.3.2d)

Offside rear brake recording little or no effort (3.7.B.5a)

Parking brake: efficiency below requirements (3.7.B.7)

Registration plate lamp not working (1.1.5c)

Service brake: efficiency below requirements (3.7.B.7)

Windscreen washer provides insufficient washer liquid (8.2.3)

Brake pedal has insufficient reserve movement (3.3.A.5) DANGEROUS

Parking brake: efficiency below requirements (3.7.B.7)

Brake hydraulic reservoir fluid level below minimum level (3.6.G.1b)

Brakes imbalanced across an axle (3.7.B.5b)

Centre Exhaust system not adequately supported (7.1.1)

Driver's seat insecure (6.2.A.1)

Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement (7.2.4b)

Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Front Upper Suspension arm has excessive play in a ball joint (2.4.G.2)

Nearside Headlamp aim beam image kick up to the offside (1.8)

Nearside Headlamp not working on main beam (1.7.5a)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Direction indicator not working (1.4.A.2c)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside rear brake recording little or no effort (3.7.B.5a)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Rear Exhaust has part of the system excessively deteriorated (7.1.1a)

Rear Exhaust mounting missing (7.1.1b)

Service brake: efficiency below requirements (3.7.B.7)

Windscreen washer provides insufficient washer liquid (8.2.3)

front brake application uneven (3.7.B.2)

rear brake application uneven (3.7.B.2)

Exhaust has a part missing (7.1.1a)

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Front Headlamp aim not tested (1.8.A.1c)

Nearside Front Headlamp not working on dipped beam (1.7.5a)

Nearside Front Headlamp not working on main beam (1.7.5a)

Nearside Rear Registration plate lamp shows direct white light to the rear (1.1.C.1f)

Offside Front Direction indicator not working (1.4.A.2c)

Offside Front Headlamp aim not tested (1.8.A.1c)

Offside Front Headlamp not working on dipped beam (1.7.5a)

Offside Front Headlamp not working on main beam (1.7.5a)

Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Suspension component mounting prescribed area is inadequately repaired (2.4.A.3)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f)

Offside Hazard warning lamps not flashing in phase, with ignition on (1.4.B.1f)

Offside Rear Registration plate lamp not working (1.1.5c)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear fog lamp not working (1.3.2b)

Offside Rear fog lamp tell tale not working (1.3.1b)

Rear Exhaust mounting missing (7.1.1b)

rear brake application uneven (3.7.B.2)

Brakes imbalanced across an axle (3.7.B.5b) DANGEROUS

Due to excessive amount of fibreglass unable to assess condition of Offside inner sill panel

Nearsise front seat belt twisted