2006 Seat Leon

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Central Exhaust has a minor leak of exhaust gases on catalyst - CLOSE TO EXCESSIVE (6.1.2 (a))

Rear Brake pipe corroded, covered in grease or other material nearside and offside (1.1.11 (c))

Rear Exhaust has a minor leak of exhaust gases at joint (6.1.2 (a))

front and rear of nearside outer sill corroded

Front Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Front Brake hose excessively deteriorated (1.1.12 (b) (ii))

Offside Front Brake hose excessively deteriorated (1.1.12 (b) (ii))

Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))

Central Exhaust has a minor leak of exhaust gases on catalyst - CLOSE TO EXCESSIVE (6.1.2 (a))

Rear Brake pipe corroded, covered in grease or other material nearside and offside (1.1.11 (c))

Rear Exhaust has a minor leak of exhaust gases at joint (6.1.2 (a))

front and rear of nearside outer sill corroded

front brake hose ferrules badly rusting

near side front tyre inner shoulder bald

off side front tyre inner shoulder worn and there is a deep cut in the inner tread area

rear of both sill panel areas and middle of near side sill area rusting

rear of off side front to rear metal brake pipe rusting

rear subframe quite badly surface rusting

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Exhaust has a major leak of exhaust gases rear box to centre joint, and cat area split also (7.1.2)

Nearside Front Lower Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

front brake hose ferrules badly rusting

near side front tyre inner shoulder bald

off side front tyre inner shoulder worn and there is a deep cut in the inner tread area

rear of both sill panel areas and middle of near side sill area rusting

rear of off side front to rear metal brake pipe rusting

rear subframe quite badly surface rusting

Front Tyre worn close to the legal limit Both inner shoulders of front tyres worn. (4.1.E.1)

Nearside Rear rear brake recording little or no effort (3.7.B.5a)

Rear rear brake binding Both rear has excessive bind (3.7.B.1)

Front Tyre worn close to the legal limit Both inner shoulders of front tyres worn. (4.1.E.1)

Nearside Headlamp aim too high (1.8)

Nearside rear brake binding (3.7.B.1)

Nearside rear parking brake recording little or no effort (3.7.B.6a)

Offside Headlamp aim too high (1.8)

Offside Registration plate lamp not working (1.1.C.1d)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside rear brake binding (3.7.B.1)

Parking brake: efficiency below requirements (3.7.B.7)

Rear registration plate deteriorated (6.3.1d)

Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone 'A' (8.3.1b)

brake disc in such a condition that it is seriously weakened rear both sides (3.5.1i)

Engine covers fitted obscuring some components in the engine bay

Nearside Rear Rear wheel bearing has slight play (2.6.2)

Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Under-trays fitted obscuring some underside components

Nearside Front Headlamp not working on dipped beam (1.7.5a)

Offside Front Headlamp aim beam image obviously incorrect (1.8.A.1b)

Offside Rear Registration plate lamp not working (1.1.C.1d)

Parking brake: efficiency below requirements (3.7.B.7)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Brake pad(s) wearing thin (3.5.1g)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside front brake fluctuating, but not excessively (3.7.B.3)

Under-trays fitted obscuring some underside components

Offside rear brake binding (3.7.B.1)

Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside rear brake binding (3.7.B.1)

Offside rear brake binding (3.7.B.1)

front discs pitted inner face