2000 Toyota Yaris

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Front Brake disc significantly and obviously worn (1.1.14 (a) (i))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Rear Exhaust has a major leak of exhaust gases box corroded. (6.1.2 (a))

Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

Offside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Brake disc worn, but not excessively both sides (1.1.14 (a) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Offside Rear Coil spring fractured or broken (5.3.1 (b) (i))

Front Anti-roll bar linkage pin or bush excessively worn both sides (5.3.4 (a) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Front Brake disc worn, but not excessively both sides (1.1.14 (a) (i))

Front Headlamp has a product on the lens but not seriously reducing light output both sides (4.1.4 (b))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement Nearside + Offside (5.3.4 (a) (i))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Rear Suspension arm pin or bush worn but not resulting in excessive movement Nearside + Offside (5.3.4 (a) (i))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i))

Nearside Front Lower Anti-roll bar linkage pin or bush excessively worn drop link rubbers perished (5.3.4 (a) (i))

Nearside Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened (5.3.1 (b) (i))

Offside Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i))

Offside Front Lower Anti-roll bar linkage pin or bush excessively worn drop link rubbers perished (5.3.4 (a) (i))

Offside Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened (5.3.1 (b) (i))

Nearside Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Offside Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Items removed from driver's view prior to test

Nearside Headlamp deteriorated but light output not reduced (1.7.5a)

Offside Headlamp deteriorated but light output not reduced (1.7.5a)

Nearside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar linkage rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Anti-roll bar ball joint dust cover damaged, but preventing the ingress of dirt (2.4.G.2)

Offside Front Anti-roll bar ball joint dust cover damaged, but preventing the ingress of dirt (2.4.G.2)

Nearside Registration plate lamp not working (1.1.5c)

Nearside Front position lamp(s) not working (1.1.A.3b)

Offside Front position lamp(s) not working (1.1.A.3b)

Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Front Brake pad(s) wearing thin (3.5.1g)

Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Headlamp aim too low (1.8)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Headlamp aim too low (1.8)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)