2003 Subaru Forester

Nearside Front Wheel bearing slightly noisy (5.1.3 (b) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i))

Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Rear Brake pad(s) worn down to wear indicator (1.1.13 (a) (i))

Trailer electrical socket likely to become detached (4.10 (a) (ii))

Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Offside Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) DANGEROUS

Brake hydraulic reservoir close to minimum mark (1.1.10 (d) (i))

Nearside Front Wheel bearing slightly noisy (5.1.3 (b) (i))

Nearside Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Windscreen wiper blade defective (3.4 (b) (i))

Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear inner arch strut mountings (5.3.6 (a) (i))

Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear inner arch and strut mountings (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive rear inner sill (5.3.6 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner sill (5.3.6 (a) (i))

Offside Rear Upper Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Nearside Rear Shock absorbers has a serious fluid leak (5.3.2 (b))

Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i))

Nearside Front Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) DANGEROUS

Brake hydraulic reservoir close to minimum mark (1.1.10 (d) (i))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Nearside Rear Shock absorber has a light misting of oil (2.7.3)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Rear Brake pipe slightly corroded (3.6.B.2c)

under trays fitted obscuring some components

Nearside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

under trays fitted obscuring some components

Offside Front Lower Front suspension ball joint dust cover damaged, but preventing the ingress of dirt (2.4.G.2)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

Nearside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Offside Front Lower Front suspension ball joint dust cover damaged, but preventing the ingress of dirt (2.4.G.2)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

brake pipes poor

exhaust pipe poor

extensive surface rust throughout chassis

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Lower Front suspension ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Offside Lower Front suspension ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

chassis and chassis mounted parts becoming corrroded

exhaust poor

n/s/r shock absorber damp

o/s headlamp wash unit broken

o/s mirror glass cracked

All position lamps not working (1.1.A.3b)

Registration plate lamp not working (1.1.C.1d)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Lower Front suspension ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Offside Lower Front suspension ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

chassis and chassis mounted parts becoming corrroded

exhaust poor

n/s/r shock absorber damp

o/s headlamp wash unit broken

o/s mirror glass cracked

Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)