2005 Kia Sorento

Front Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Front Oil leak, but not excessive (8.4.1 (a) (i))

Front and Rear general rust underneath

Nearside Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security outer integral body (6.2.2 (d) (i))

Offside Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security outer integral body (6.2.2 (d) (i))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Outer Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security Sill, side skirt fitted (6.2.2 (d) (i))

Nearside Rear Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Nearside Rear Inner Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security sill (6.2.2 (d) (i))

Offside Outer Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security Sill, side skirt fitted (6.2.2 (d) (i))

Offside Rear Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))

Central Front Oil leak, but not excessive (8.4.1 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material Front to rear. (1.1.11 (c))

Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Rear Brake pipe corroded, covered in grease or other material Front to rear. (1.1.11 (c))

Items removed from driver's view prior to test ()

Propshaft universal joint worn rear of front has slight play ()

clutch slave cylinder leaking fluid

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

engine covers fitted not allowing a full inspection

items removed from drivers view before test

oil leak

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

clutch slave cylinder leaking fluid

engine covers fitted not allowing a full inspection

items removed from drivers view before test

oil leak

Engine covers fitted obscuring some components in the engine bay

Items removed from driver's view prior to test

Nearside Front Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Nearside Rear Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Offside Front Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Offside Rear Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Oil leak

Parking brake lever has little reserve travel (3.1.6b)

Coolant leak

Rear Anti-roll bar has slight play in a pin/bush (2.4.G.2)

front propshaft missing

wheelarch/sill covers fitted

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Offside Rear rear brake binding (3.7.B.1)

Rear Anti-roll bar has slight play in a pin/bush (2.4.G.2)

front propshaft missing

wheelarch/sill covers fitted

Oil leak

Slight bind N/S/R Brake felt by hand only.

Nearside Registration plate lamp not working (1.1.C.1d)

Nearside Stop lamp not working (1.2.1b)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Parking brake lever has no reserve travel (3.1.6b)

Parking brake: efficiency below requirements (3.7.B.7)

Brake hydraulic reservoir fluid close to minimum level (3.6.G.1b)

Nail in offside rear tyre

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Oil leak

uneven wear on offside front tyre

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)