2000 Mercedes-benz Sprinter

Nearside Headlamp aim projected beam image is obviously incorrect dip beam (4.1.2 (c))

Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength spring front hanger outer sill area (5.3.6 (a) (i))

Offside Front Brake hose ferrule excessively corroded (1.1.12 (f) (i))

Offside Front Brake pipe excessively corroded (1.1.11 (c))

Offside Front Headlamp aim projected beam image is obviously incorrect dip beam (4.1.2 (c))

Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength spring front hanger - inner sill/chassis (5.3.6 (a) (i))

Rear Registration plate does not conform to the specified requirements (0.1 (d))

Nearside Rear Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis -rear spring swinging hanger (5.3.6 (a) (ii)) DANGEROUS

Offside Rear Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis near the rear swinging hanger (5.3.6 (a) (ii)) DANGEROUS

Service brake requirements only just met. It would appear that the braking system requires adjustment or repair All wheels only just met the requirements on the service brake and also on the parking brake - Needs attention (1.2.1 (c))

Vehicle structure is corroded but structural rigidity is not significantly reduced General condition of chassis - has heavy surface corrosion in various areas (6.1.1 (c) (i))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Shock absorbers has slight external damage to the casing (5.3.2 (b))

Nearside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Nearside Rear Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Shock absorbers has slight external damage to the casing (5.3.2 (b))

Offside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Rear Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

n/s/r outer sill corroded and holed.

Service brake efficiency below requirements (1.2.2 (a) (i))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Shock absorbers has slight external damage to the casing (5.3.2 (b))

Nearside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Nearside Rear Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Shock absorbers has slight external damage to the casing (5.3.2 (b))

Offside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Rear Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

n/s/r outer sill corroded and holed.

Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Shock absorbers has slight external damage to the casing (5.3.2 (b))

Nearside Rear Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Nearside Suspension component mounting repair covered in underseal inner and outer sill area (5.3.6 (a) (i))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Shock absorbers has slight external damage to the casing (5.3.2 (b))

Offside Rear Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Suspension component mounting repair covered in underseal inner and outer sill area (5.3.6 (a) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

n/s/r outer sill holed

Nearside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Nearside Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced weld by rear bump stop does not meet standards ..must be a continuous for patches (6.1.1 (d) (i))

Nearside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Nearside Front Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Central Rear Vehicle structure fractured seriously affecting its strength within 30cm of towbar mounting (6.1.6 (i) (i))

Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked with chalk (5.3.6 (a) (i))

Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength bump stop mount (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked with chalk (5.3.6 (a) (i))

Nearside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Nearside Front Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Nearside Outer Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Nearside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Front Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Offside Outer Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Rear Shock absorbers has a slightly worn bush (5.3.2 (c))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Smoke Limit Plate Defaced

Steering system slightly rough (2.1.1 (a))

Nearside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i))

Offside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Smoke Limit Plate Defaced

Steering system slightly rough (2.1.1 (a))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Smoke Limit Plate Defaced

Exhaust emissions exceed level of metered smoke for a turbo charged engine 0.86 (8.2.2.2 (b))

Headlamp levelling device inoperative (4.1.5 (a))

Nearside Front Anti-roll bar linkage pin or bush excessively worn both (5.3.4 (a) (i))

Nearside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage pin or bush excessively worn both (5.3.4 (a) (i))

Offside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i))

Offside Rear fog lamp not working (4.5.1 (a) (ii))

Rear Brakes imbalanced across an axle 46% (1.2.1 (b) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Rear fog lamp switch missing (4.5.3 (a))

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Front Lower Suspension component ball joint has slight play has lift (5.3.4 (a) (i))

Offside Front Lower Suspension component ball joint has slight play has lift (5.3.4 (a) (i))

Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f))

Nearside Drag link end ball joint has excessive play (2.1.3 (b) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Rear fog lamp switch missing (4.5.3 (a) (ii))

Nearside Front Lower Suspension component ball joint has slight play has lift (5.3.4 (a) (i))

Offside Front Lower Suspension component ball joint has slight play has lift (5.3.4 (a) (i))

Brake pipe corroded, covered in grease or other material front to rears (1.1.11 (c))

Nearside Drag link end ball joint has slight play (2.1.3 (b) (i))

Nearside Front Inner Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Lower Suspension component ball joint has slight play (5.3.4 (a) (i))

Offside Front Lower Suspension component ball joint has slight play (5.3.4 (a) (i))

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Front Brake pipe slightly corroded to rear (3.6.B.2c)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Brake pipe slightly corroded to rear (3.6.B.2c)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Nearside Rear reflector missing (1.5.1a)

Offside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Front Brake pipe slightly corroded to rear (3.6.B.2c)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Brake pipe slightly corroded to rear (3.6.B.2c)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

rear parking (secondary) brake imbalance requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.6b)

Front Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Nearside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

hub caps fitted

undershields fitted

Rear Brakes imbalanced across an axle (3.7.B.5b)

Front Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Nearside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

hub caps fitted

n/s/r pads look low

undershields fitted

Nearside Front Lower Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Nearside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Lower Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Offside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

exhaust tail pipe missing.

Offside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Front Brake pipe slightly corroded (3.6.B.2c)

Nearside Front Lower Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Nearside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Lower Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Offside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

exhaust tail pipe missing.

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Nearside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

front disc worn

Brake hydraulic reservoir fluid level below minimum level (3.6.G.1b)

Centre Exhaust has a major leak of exhaust gases (7.1.2)

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Rear rear brake recording little or no effort (3.7.B.5a)

Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Rear rear brake recording little or no effort (3.7.B.5a)

Offside Rear rear parking brake recording little or no effort (3.7.B.6a)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Rear Exhaust system not adequately supported (7.1.1)

Brakes imbalanced across an axle (3.7.B.5b) DANGEROUS

Nearside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

front disc worn

Front Brake pad(s) wearing thin (3.5.1g)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Steering rack damaged but serviceable (2.2.C.1d)

Front Brake pad(s) wearing thin (3.5.1g)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Stop lamp not working (1.2.1b)

Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Steering rack damaged but serviceable (2.2.C.1d)

Nearside rear brake juddering slightly (3.7.A.5b)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Steering rack damaged but serviceable (2.2.C.1d)

nearside wiper blade worn

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

hand brake lever travels high