2000 Iveco Daily

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Brake hose slightly deteriorated (1.1.12 (b) (ii))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced under bonet (6.1.1 (c) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material load valve (1.1.11 (c))

Offside Front Brake hose slightly deteriorated (1.1.12 (b) (ii))

Suspension component mounting repair covered in underseal all welding (5.3.6 (a) (i))

sill covers fitted

Nearside Rear Position lamp not working (4.2.1 (a) (ii))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Brake hose slightly deteriorated (1.1.12 (b) (ii))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced under bonet (6.1.1 (c) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material load valve (1.1.11 (c))

Offside Front Brake hose slightly deteriorated (1.1.12 (b) (ii))

Suspension component mounting repair covered in underseal all welding (5.3.6 (a) (i))

sill covers fitted

Exhaust emissions exceed manufacturer's specified limit 1.00 (8.2.2.2 (a))

Nearside Headlamp aim too low (4.1.2 (a))

Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis mount (6.1.1 (c) (i))

Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis mount (6.1.1 (c) (i))

Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis mount (6.1.1 (c) (i))

Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis mount (6.1.1 (c) (i))

Nearside Rear Anti-roll bar pin or bush likely to become detached missing (5.3.4 (a) (ii)) DANGEROUS

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Brake hose slightly deteriorated (1.1.12 (b) (ii))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced under bonnet (6.1.1 (c) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material load sence valve (1.1.11 (c))

Nearside Rear reflector insecure (4.8.1 (b) (i))

Offside Front Brake hose slightly deteriorated (1.1.12 (b) (ii))

Oil leak, but not excessive (8.4.1 (a) (i))

Suspension component mounting repair covered in underseal under van (5.3.6 (a) (i))

sill covers fitted

Exhaust emissions exceed manufacturer's specified limit 1.00 (8.2.2.2 (a))

Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inside arch (6.1.1 (c) (i))

Nearside Headlamp aim too low (4.1.2 (a))

Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis mount (6.1.1 (c) (i))

Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear out rigger (6.1.1 (c) (i))

Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis mount (6.1.1 (c) (i))

Nearside Rear Position lamp not working (4.2.1 (a) (ii))

Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i))

Offside Brake master cylinder/servo mounting prescribed area is excessively corroded under bonnet (1.1.21 (e) (i))

Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inside arch (6.1.1 (c) (i))

Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under bonnet (6.1.1 (c) (i))

Offside Front Integral body structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis mount (6.1.1 (c) (i))

Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear outrigger (6.1.1 (c) (i))

Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis mount (6.1.1 (c) (i))

Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i))

Offside Rear reflector missing (4.8.2 (a) (ii))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Nearside Rear Anti-roll bar pin or bush likely to become detached missing (5.3.4 (a) (ii)) DANGEROUS

Battery insecure but not likely to fall from carrier (4.13 (a) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Brake hose slightly deteriorated (1.1.12 (b) (ii))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced under bonnet (6.1.1 (c) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material load sence valve (1.1.11 (c))

Nearside Rear reflector insecure (4.8.1 (b) (i))

Offside Front Brake hose slightly deteriorated (1.1.12 (b) (ii))

Oil leak, but not excessive (8.4.1 (a) (i))

Suspension component mounting repair covered in underseal under van (5.3.6 (a) (i))

sill covers fitted

Brake fluid warning lamp defective (1.1.10 (f))

Front Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Nearside Rear Fluid leak, but not excessive (8.4.1 (a) (i))

Offside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Rear Fluid leak, but not excessive (8.4.1 (a) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brake load sensing valve linkage defective and function impaired (1.1.17 (a))

Service brake efficiency below requirements (1.2.2 (a) (i))

Brake fluid warning lamp defective (1.1.10 (f))

Front Anti-roll bar corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Nearside Rear Fluid leak, but not excessive (8.4.1 (a) (i))

Offside Front Suspension component mounting repair covered in underseal (5.3.6 (a) (i))

Offside Rear Fluid leak, but not excessive (8.4.1 (a) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

General corrosion to underside of vehicle

Nearside Front Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Nearside Rear Direction indicator slightly affected by the operation of another lamp (4.4.3 (b))

Nearside Rear Direction indicator slightly discoloured (4.4.3 (a))

Nearside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced Body - not within prescribed area (6.1.1 (c) (i))

Offside Rear Direction indicator slightly affected by the operation of another lamp (4.4.3 (b))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Direction indicator lens defective such that the emitted light is adversely affected (4.4.1 (b) (ii))

Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg (6.1.1 (c) (i))

Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg (6.1.1 (c) (i))

General corrosion to underside of vehicle

Nearside Front Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Nearside Rear Direction indicator slightly affected by the operation of another lamp (4.4.3 (b))

Nearside Rear Direction indicator slightly discoloured (4.4.3 (a))

Nearside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced Body - not within prescribed area (6.1.1 (c) (i))

Offside Rear Direction indicator slightly affected by the operation of another lamp (4.4.3 (b))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear chassis heavily corroded

brake warning lamp on

Nearside Inner Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i))

Nearside Inner Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i))

Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i))

Nearside Rear Brake pipe excessively corroded (1.1.11 (c))

Nearside Rear Position lamp not working (4.2.1 (a) (ii))

Offside Front Brake pipe excessively corroded (1.1.11 (c))

Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i))

Offside Front Outline marker lamp not working (4.2.1 (a) (ii))

Offside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i))

Offside Rear Brake pipe excessively corroded (1.1.11 (c))

Offside Rear Direction indicator not working (4.4.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Registration plate lamp does not illuminate simultaneously with the position lamps (4.7.2 (a))

Service brake efficiency below requirements (1.2.2 (a) (i))

Rear Brake load sensing valve inoperative and ABS not fitted or inoperative (1.1.17 (c) (ii)) DANGEROUS

Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Electrical wiring insecure pad sensor +brake warning lamp on (4.11 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Outer Oil leak, but not excessive hubs (8.4.1 (a) (i))

Rear chassis heavily corroded

Brake load sensing valve linkage defective and function impaired (1.1.17 (a))

Nearside Front Suspension component mounting prescribed area is inadequately repaired out rigger / body to chassis mount area not fully welded (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is inadequately repaired front leaf spring mount / outrigger (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is inadequately repaired rear leaf spring mount / outrigger (5.3.6 (a) (i))

Offside Front Outline marker lamp not working (4.2.1 (a) (ii))

Offside Rear Suspension component mounting prescribed area is inadequately repaired front leaf spring mount / outrigger (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is inadequately repaired rear leaf spring mount / outrigger (5.3.6 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Front Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Nearside Front Vehicle structure is corroded but structural rigidity is not significantly reduced outer sill corroded but not within prescribed area (6.1.1 (c) (i))

Nearside Rear Direction indicator slightly discoloured (4.4.3 (a))

Offside Front Vehicle structure is corroded but structural rigidity is not significantly reduced inner and outer sill corroded but not within prescribed area (6.1.1 (c) (i))

Offside Front indicator loose but not insecure

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear of vehicle floor area getting rusty

Vehicle structure is corroded but structural rigidity is not significantly reduced Rear bumper mount area rusty (6.1.1 (c) (i))

Brake load sensing valve inoperative but ABS functioning (1.1.17 (c) (i))

Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch / front subframe mount (6.1.1 (c) (i))

Nearside Rear Parking brake inoperative on one side (1.4.1 (a))

Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch / rear outer rigger (6.1.1 (c) (i))

Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch / front subframe mount (6.1.1 (c) (i))

Offside Rear Anti-roll bar pin or bush excessively worn inner D bush (5.3.4 (a) (i))

Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch / front outer rigger and sill end (6.1.1 (c) (i))

Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch / rear outer rigger in TWO places (6.1.1 (c) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brakes imbalanced across an axle (1.2.1 (b) (i))

Front fuel tank bracket damaged

Nearside Front inner wheel arch cover loose

Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement inner D bush (5.3.4 (a) (i))

Nearside Rear Direction indicator slightly discoloured (4.4.3 (a))

Nearside Rear Vehicle structure is corroded but structural rigidity is not significantly reduced inner wheel arch / front out rigger (6.1.1 (c) (i))

Nearside Vehicle structure is corroded but structural rigidity is not significantly reduced Centre inner sill corroded but not within prescribed area (6.1.1 (c) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Vehicle structure is corroded but structural rigidity is not significantly reduced inner sill corroded but not within prescribed area (6.1.1 (c) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Oil leak, but not excessive Rear diff outer sills (8.4.1 (a) (i))

Rear Bumper mountings corroded but not likely to become detached bumper mount area getting rusty (6.1.4 (a) (i))

Rear diff noisy when rear wheels rotated

Brake pipe corroded, covered in grease or other material both front metal pipes (1.1.11 (c))

battery insecure but not likely to fall out or over

o//s/r inner anti roll bar bush has slight play

Parking brake efficiency below requirements (1.4.2 (a) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps both (4.7.1 (b) (ii))

Service brake efficiency below requirements (1.2.2 (a) (i))

Brake pipe corroded, covered in grease or other material both front metal pipes (1.1.11 (c))

battery insecure but not likely to fall out or over

o//s/r inner anti roll bar bush has slight play

Parking brake efficiency below requirements (1.4.2 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Headlamp aim too low (1.8)

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords and worn close to limit (4.1.D.1a)

Offside Registration plate lamp not working (1.1.C.1d)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a) DANGEROUS

corrosion in body and bulk head

extensive welding repairs carried unable to fully access due to being covered in sealer

Nearside Rear Shock absorber has a serious fluid leak (2.7.3)

corrosion in body and bulk head

extensive welding repairs carried unable to fully access due to being covered in sealer

Nearside Inner Seat belt anchorage prescribed area is corroded but not considered excessive sill (5.2.6)

brake pipes coordded

engine oil leak

inner sills floors corodded

plastic outer sill covers fitted

Nearside Front Upper Anti-roll bar has excessive play in a ball joint (2.4.G.2)

Nearside Rear Direction indicator not working (1.4.A.2c)

Offside Inner Seat belt anchorage prescribed area is excessively corroded sill (5.2.6)

Rear Brake lever has restricted free movement (3.5.1k)

Rear Brake rod insecure (3.5.1d)

Service brake: efficiency below requirements (3.7.B.7)

Nearside Inner Seat belt anchorage prescribed area is corroded but not considered excessive sill (5.2.6)

brake pipes coordded

engine oil leak

inner sills floors corodded

plastic outer sill covers fitted

Body has slight corrosion (6.1.B.2)

Nearside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Oil leak

Vehicle structure has slight corrosion (6.1.A.1)

rear hub seals leaking oil

Front Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front Tyre has ply or cords exposed (4.1.D.1b) DANGEROUS

Service brake: efficiency below requirements (3.7.B.7) DANGEROUS

Body has slight corrosion (6.1.B.2)

Nearside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Oil leak

Rear Brake pad(s) wearing thin (3.5.1g)

Vehicle structure has slight corrosion (6.1.A.1)

rear hub seals leaking oil

Body has slight corrosion (6.1.B.2)

Oil leak

Power steering pipe(s) or hose(s) has slight seepage (2.3.3b)

Vehicle structure has slight corrosion (6.1.A.1)

nearside front side marker not working

offside rear sill damaged

Brake fluid warning lamp illuminated (3.6.G.2)

Body has slight corrosion (6.1.B.2)

Oil leak

Power steering pipe(s) or hose(s) has slight seepage (2.3.3b)

Vehicle structure has slight corrosion (6.1.A.1)

nearside front side marker not working

offside rear sill damaged

Nearside Rear Shock absorber has a light misting of oil (2.7.3)

Offside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Brake load sensing valve linkage defective and function impaired (3.6.E.3)

Service brake: efficiency below requirements (3.7.B.7)

Brake load sensing valve linkage stiff (3.6.E.3)

Front registration plate character(s) incorrectly spaced (6.3.4a)

Nearside Rear Shock absorber has a light misting of oil (2.7.3)

Offside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Rear registration plate character(s) incorrectly spaced (6.3.4a)

Brakes imbalanced across an axle (3.7.B.5b)

Rear Brake load sensing valve linkage defective and function impaired (3.6.E.3)

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Nearside Rear wheel bearing has slight play (2.6.2)

Offside Rear Direction indicator slightly discoloured (1.4.A.2f)

Centre Exhaust mounting missing (7.1.1b)

Offside Front Suspension arm has excessive play in a pin/bush (2.4.G.2)

Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Rear Shock absorber detached (2.7.2b)

Offside Registration plate lamp not working (1.1.5c)

Oil leak

Nearside Front Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Suspension arm has slight play in a ball joint (2.4.G.2)