2000 Mercedes-benz Sprinter

Fuel tank insecure (6.1.3 (a) (i))

Horn not working (7.7 (a) (ii))

Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Nearside Rear Direction indicator not working (4.4.1 (a) (ii))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Position lamp showing white light to the rear (4.2.3 (a) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Registration plate lamp does not illuminate simultaneously with the position lamps (4.7.2 (a))

Offside Registration plate lamp does not illuminate simultaneously with the position lamps (4.7.2 (a))

Rear fog lamp does not emit a steady red light (4.5.4 (a))

Steering column has excessive movement up and down (2.2.2 (a))

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

Brake pipe inadequately clipped or supported (1.1.11 (d) (i))

Nearside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Offside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Brake hose excessively damaged both front (1.1.12 (b) (ii))

Brake load sensing valve linkage defective and function impaired spring broken (1.1.17 (a))

Fuel cap/sealing device missing (6.1.3 (b) (i))

Headlamp aim too low both (4.1.2 (a))

Nearside Headlamp not working on main beam (4.1.1 (a) (ii))

Nearside Rear Position lamp missing (4.2.1 (a))

Offside Outline marker lamp not working (4.2.1 (a))

Offside Rear Outer Position lamp not working (4.2.1 (a))

Offside Side repeater not working (4.4.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear fog lamp not working (4.5.1 (a) (ii))

Registration plate lamp missing in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Windscreen damaged and affecting the driver's view of the road (3.2 (a) (ii))

Nearside Front Body has a sharp edge caused by corrosion outer step sill (6.1.C.1)

Nearside Front Brake hose excessively deteriorated (3.6.B.4d)

Nearside Front Front position lamp(s) not working marker light (1.1.A.3b)

Nearside Rear Brake hose excessively deteriorated (3.6.B.4d)

Nearside Rear Front position lamp(s) not working marker light (1.1.A.3b)

Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Offside Front Body has a sharp edge caused by corrosion outer step sill (6.1.C.1)

Offside Front Body has a sharp edge caused by corrosion rear of cab (6.1.C.1)

Offside Front Brake hose excessively deteriorated (3.6.B.4d)

Offside Front Front position lamp(s) not working marker light (1.1.A.3b)

Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Rear Front position lamp(s) not working marker light (1.1.A.3b)

Offside Rear Rear position lamp(s) adversely affected by the operation of another lamp (1.1.A.3f)

Offside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a)

Offside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)

Parking brake: efficiency below requirements (3.7.B.7)

Nearside Front Anti-roll bar linkage rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Rear position lamp(s) damaged, but still visible from a reasonable distance (1.1.A.3d)

Offside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Brake load sensing valve linkage stiff (3.6.E.3)

Brake load sensing valve stiff (3.6.E.3)

Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Front Brake pad(s) wearing thin (3.5.1g)

Front Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Nearside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Offside Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

nearside front shocker has play in shaft

offside front shocker has play on shaft

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Front Brake pipe excessively corroded (3.6.B.2c)

Offside Front Suspension arm has excessive play in a ball joint (2.4.G.2)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Anti-roll bar has excessive play in a pin/bush (2.4.G.2)

Brake pipe excessively corroded (3.6.B.2c)

Nearside Front Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2)

Nearside Front Shock absorber has negligible damping effect (2.7.5)

Nearside Side repeater not working (1.4.A.2c)

Offside Front Anti-roll bar has excessive play in a pin/bush (2.4.G.2)

Offside Front Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Brake pipe slightly corroded (3.6.B.2c)

Offside Front Suspension arm has slight play in a ball joint (2.4.G.2)